Javelin J420i Скачать руководство пользователя страница 39

Страница: 39 / 60

General

information

Getting

Started

Operation

Starting to

Print Cards

Cleaning

Trouble

Shooting

Technical

Specifications

Rev. 1.3

TROUBLESHOOTING

•

Printing shows very pale or inconsistent results.

Possible Cause

A. Ribbon may have been stored improperly or is damaged.

B. Cards may not meet specifications.

C. Contrast and/or Intensity may be set to values

which are too high.

D. Dust or embedded contamination on elements

of the Printhead.

Solution

A1.Change ribbon and print again.

B1.Use a different supply of cards.

C1. Adjust contrast and/or Intensity values in software

D1.Perform a cleaning of the Printhead (see 4.2 Cleaning the printhead.)

•

Printing shows blurry printed image.

Possible Cause

A. Ribbon may not be correctly positioned

B. Ribbon may not be synchronized on the correct

colour panel position.

C. Cards may not meet specifications.

D. Dust inside the printer and/or dirty cleaning roller.

Solution

A1. Open cover and press down the printhead unlock lever to open the

printhead carriage. The printhead will move up.

A2. Check ribbon is properly rolled on ribbon cores.

A3. Push down on the printhead lock lever until an audible

“

click

”

signals the locked-down position.

A4. Ribbon will automatically synchronize.

A5. Print again.

Continued on next page...

➔

Содержание J420i





























































Результаты поиска

Содержание J420i

Отзывы:

Похожие инструкции для J420i

Бренды по названию

Популярные бренды

Javelin J420i, Руководство пользователя

Результаты поиска

Содержание J420i

Отзывы:

Похожие инструкции для J420i

Бренды по названию

Популярные бренды