background image

Jason International, Inc.  •  

 

501.771.4477  

 

 

 

Page 1 of 18

 

 

 

 

Customer Service :  800.255.5766 

Copyright © 2011 Jason International.

“TO BE REMOVED FOR USE BY THE OCCUPANT.”

49-1012-100 

Date   03/11

Owner’s Manual

Designer whirlpool Baths

InsTallaTIOn, OPeraTIOn, anD MaInTenanCe

Jason International, Inc.

 

8328 MacArthur Drive

North Little Rock, AR 72118
www.jasoninternational.com

Owner’s reCOrD

Dealer: 

Date Purchased: 

Date Installed: 

Installer: 

PlaCe serIal nuMBer CarD wITh 

PrODuCT COnfIguraTIOn In ThIs BOx

InsPeCTIOn

Inspect the unit prior to installation. In the event of a 

problem, DO NOT install the unit.

  

All components are factory assembled to the bath and the 
unit is water tested and inspected prior to leaving Jason 
International, Inc.

If the carton shows sign of damage, inspect the product 
before accepting and describe the problem on the Bill of 
Lading.

NOTe: Transportation and insurance from Jason’s 

factory are the buyer’s responsibility.

Damage sustained in transit is the responsibility of the 

carrier.

 If damage is discovered, 

If  the  carton  shows  sign  of  damage,  inspect 

the product before accepting and describe the 

problem on the Bill of lading.

the carrier must be immediately notified in writing with a 
request for a representative to inspect the unit. Failure of 
the carrier to respond should be reported to the seller and 
carrier. Always file a freight claim promptly.

The installer is responsible for insuring that the unit is 
free from defects or shipping damage. In the event of a 
problem, DO NOT install the unit. 
Jason International is not responsible for damage that 
might have been avoided by inspection or testing prior to 
installation.

Damage to the unit during installation will not be covered 
by warranty and is the responsibility of the installer. ALL 
WARRANTY CLAIMS ON ACRYLIC SURFACE DAMAGE 
MUST BE MADE PRIOR TO INSTALLATION. Inspect 
plumbing and bath surface for missing or damaged 
components. Alert your dealer of any discrepancies.

To protect the unit from damage keep the bath in the 
carton until ready for installation.

Содержание CC550



















Отзывы: