Jacobsen 67069 Скачать руководство пользователя страница 49

Страница: 49 / 56

QUALITY OF CUT 11

11.4 STEP CUTTING____________________________________________________________

NOTE:

Arrow indicates direction of travel.

Step cutting occurs when grass is cut taller on one side of
a reel than the other or one cutting unit to another. This is
usually caused by mechanical wear or an incorrect roller
or HOC (height-of-cut) adjustment.

Probable Cause

Remedy

HOC (height-of-cut) settings are different from one
side of a reel to the other or from one cutting unit to
another.

Check HOC adjustment of cutting units.

Worn front roller bearings.

Check/replace front roller bearings.

Reel-to-bedknife contact is different from one side of
the cutting unit to the other or from one cutting unit to
another.

Check reel-to-bedknife contact.

Cutting reel movement is restricted.

Check/remove cutting reel movement obstruction.

Variations in turf density.

Change mowing direction.

Machine weight distribution is uneven.

Check/adjust tire inflation pressure.

TN0221

Содержание 67069

























































Результаты поиска

Содержание 67069

Отзывы:

Похожие инструкции для 67069

Бренды по названию

Популярные бренды

Jacobsen 67069, Руководство по эксплуатации

Результаты поиска

Содержание 67069

Отзывы:

Похожие инструкции для 67069

Бренды по названию

Популярные бренды