Jacobsen 67069 Скачать руководство пользователя страница 52

Страница: 52 / 56

11 QUALITY OF CUT

11.7 STREAKS ________________________________________________________________

NOTE:

Arrow indicates direction of travel.

A streak is a line of uncut grass. This is usually caused by
a nicked or bent bedknife.

Probable Cause

Remedy

Damaged bedknife.

Replace bedknife.

Damaged or unevenly worn reel.

Inspect reel. Replace as needed.

Loose or missing bedknife fasteners.

Check bedknife screws. Tighten loose screws; replace
missing screws.

Turning too aggressively. Cutting units don’t overlap
around turns or on side hills.

Turn less aggressively to allow cutting units to overlap.
Change mowing direction or pattern on side hills.

Tire mats down grass before it is cut.

Check/adjust tire inflation pressure.

Wet grass is matted down before it is cut.

Mow when grass is dry.

TN0224

Содержание 67069

























































Результаты поиска

Содержание 67069

Отзывы:

Похожие инструкции для 67069

Бренды по названию

Популярные бренды

Jacobsen 67069, Руководство по эксплуатации

Результаты поиска

Содержание 67069

Отзывы:

Похожие инструкции для 67069

Бренды по названию

Популярные бренды