Jacobsen 67069 Скачать руководство пользователя страница 46

Страница: 46 / 56

10 PROBLEM SOLVING

PROBLEM SOLVING

10.1 GENERAL ________________________________________________________________

The troubleshooting chart below lists basic problems that may occur during start-up and operation. For more detailed
information regarding the hydraulic and electrical systems contact your area Jacobsen Dealer.

Symptoms

Possible Causes

Action

Engine will not start.

Parking brake disengaged, traction
pedal not in Neutral or reel/3WD
switch on.

Check operator back-up system and start-up proce-
dure.

Battery low on charge or
defective.

Inspect condition of battery and battery connections.

Fuel tank empty or dirty.

Fill with fresh fuel. Change fuel filter. Bleed fuel lines.

Fuse blown.

Replace fuse.

Engine hard to start or
runs poorly.

Fuel level low, fuel or fuel filter
dirty.

Fill with fresh fuel. Change fuel filter. Bleed fuel lines.

Air cleaner dirty.

Inspect and replace air filter.

Injectors, fuel pump.

Consult engine manual.

Engine problem.

Consult engine manual.

Engine stops.

Fuel tank empty.

Fill with fresh fuel and bleed fuel lines.

Interlocks not set before leaving
operator’s seat.

Engage parking brake, move traction lever to “N” and
set reel control to OFF.

Engine overheating.

Coolant level low.

Inspect and add coolant.

Air intake restricted.

Clean cooling air intake.

Water pump belt broken or loose.

Tighten or replace belt.

Engine overload.

Reduce forward speed.

Battery not holding
charge.

Loose or corroded battery termi-
nals.

Inspect and clean terminals.

Low electrolyte.

Refill to correct level.

Alternator belt loose or broken.

Tighten or replace belt.

Charging system defective.

See engine manual.

Reels cut unevenly.

Bedknife-to-reel not adjusted cor-
rectly.

Inspect bedknife-to-reel adjustment.

Engine speed too low.

Check engine speed. Run engine at full throttle.

Low hydraulic oil.

Check reservoir level and fill if needed.

Mower does not react
to traction pedal.

Parking brake engaged.

Disengage parking brake.

Tow Valve Open.

Close Tow Valve.

Low hydraulic oil.

Check reservoir level and fill if needed.

Implement does not
raise or lower.

Low hydraulic oil.

Check reservoir level and fill as needed.

Gauges/Indicator not
operating.

Circuit Breaker.

Reset circuit breaker, check bulb.

Loose wiring.

Check electrical connections.

Содержание 67069

























































Результаты поиска

Содержание 67069

Отзывы:

Похожие инструкции для 67069

Бренды по названию

Популярные бренды

Jacobsen 67069, Руководство по эксплуатации

Результаты поиска

Содержание 67069

Отзывы:

Похожие инструкции для 67069

Бренды по названию

Популярные бренды