Jacobsen 67069 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 56

background image

3 SPECIFICATIONS

6

3

SPECIFICATIONS

3.1 PRODUCT IDENTIFICATION _________________________________________________

67069 .............................. Tri-King Mower, 3WD, 17.7 hp

diesel engine with ROPS. Without
front lift arms or mowers.

67146 .............................. Tri-King Mower, 3WD, 17.7 hp Tier

4 diesel engine with ROPS.
Without front lift arms or mowers.

Serial Number ................ An identification plate, like the one

shown, listing the serial number, is
attached to the frame of the
mower and is located to the
operator’s left just behind the front
wheel motor. Always provide the
serial number of the unit when
ordering replacement parts or
requesting service information.

3.2

ENGINE__________________________________________________________________

Make ............................... Kubota
Model .............................. D722-E3B (67069)
Model .............................. D722-E4B (67146)
Horsepower..................... 17.7 hp (13.2 kW) @ 3200 rpm
Note:

Actual sustained horsepower will likely be lower

than listed in specifications due to operating limitations
and environmental factors

Displacement .................. 43.88 cu. in. (719 cc)
Torque ............................. 26 ft. lbs. (35 Nm) @ 2600 rpm
Fuel:

Type .......................... No. 2 Low or Ultra-Low Sulfur

Diesel

Rating ....................... Min. Cetane rating 45

Capacity.................... 6.5 U.S. Gal. (24.6 liters)

Governor......................... Ball Type Governor

Low Idle ................... 1450 RPM
High Idle ................... 3400 RPM

Lubrication:

Capacity.................... 3.4 quarts (3.2 liter) with filter

Type .......................... SAE 20W, SAE 30W
API Classification ..... CD, CE

Air Filter .......................... Dry type with evacuator valve and

service indicator

Alternator ........................ 40 amp

3.3

CUTTING UNITS: __________________________________________________________

Reel ................................ 3 Reels, 26 in. (660 mm) wide or,

3 Reels, 30 in. (762 mm) wide.

Reel Diameter ................. 7 in. (178 mm)
Bearings.......................... Self adjusting tapered roller

bearings

Blade Options ................. 7 blades
Cutting Width:

26 in. Reels ............... 72 in. (1828 mm)
30 in. Reels ............... 84 in. (2134 mm)

Overall Width:

26 in. Reels ............... 78.5 in. (1994 mm)
30 in. Reels ............... 90.5 in. (2298 mm)

Cutting Frequency:

7 Blade...................... 0.151 in./mph (3.8 mm/kph)

Product

EEC Sound

Power

Sound Pressure

Level

Operator Ear

Vibration M/S

2

Arms

Body

67069
67146

99 dba

86 dba

3.78

0.016

11524 WILMAR BLVD,

CHARLOTTE, NC 28273

®

kg

kW

1-800-848-1636 (US)

PRODUCT OF U.S.A.

A Textron Company

619

13.2

XXXX

67069001651

«
...
4
5
6
7
8
...
»

Содержание 67069

























































Отзывы:

Нет отзывов

Похожие инструкции для 67069

Бренд: SANLI Страницы: 16

Бренд: Parklander Страницы: 42

Бренд: Gardenline Страницы: 28

Бренд: Stihl Страницы: 514

215012, 215014, R215012, N2151

Бренд: Snapper Страницы: 52

Бренд: Gardif Страницы: 22

Бренд: MTD Страницы: 16

Poulan Pro 961140016

Бренд: Poulan Pro Страницы: 2

Бренд: Toro Страницы: 24

Бренд: Craftsman Страницы: 36

Бренд: Royal Страницы: 64

Бренд: Black & Decker Страницы: 4

Бренд: Black & Decker Страницы: 8

Бренд: Black & Decker Страницы: 9

Бренд: Black & Decker Страницы: 8

Бренд: Black & Decker Страницы: 164

Бренд: Black & Decker Страницы: 2

Бренд: Bushranger Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды