Jacobsen 67069 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 56

background image

9 ADJUSTMENTS

38

9.4

NEUTRAL AND 3WD SWITCHES _____________________________________________

1.

Check traction pedal adjustment.

2.

Use a volt/ohm meter to determine when switch
opens or closes.

a.

Adjust switch

(G)

so “finger” of actuating arm

(F)

is centered over sensing portion of switch.
Switch contacts should be closed with traction
pedal in neutral and open with minimal pedal
travel in forward or reverse direction.

b.

Adjust 3WD switch

(H)

so contacts are open with

traction pedal in neutral, and contacts close with
minimal pedal travel in forward direction.

Figure 9C

9.5

PARKING BRAKE SWITCHES _______________________________________________

Loosen screws (

K

) and adjust both switches so contacts

just close as the brake lever is moved to the engaged
position then tighten screws.

Figure 9D

9.6

LIFT LIMIT SWITCH ________________________________________________________

The lift limit switch must be adjusted so the reels stop
turning before the cutting plane between the reel and
ground reach 15-3/4 in. (400 mm). To adjust, loosen
screw (

L

), and adjust arm (

M

).

Figure 9E

G

H

F

K

L

M

«
...
36
37
38
39
40
...
»

Содержание 67069

























































Отзывы:

Нет отзывов

Похожие инструкции для 67069

Бренд: Gravely Страницы: 52

Бренд: MTD Страницы: 37

Бренд: Garland Страницы: 64

Бренд: VonHaus Страницы: 12

Бренд: SaMASZ Страницы: 41

Бренд: Yard-Man Страницы: 6

Бренд: Jacobsen Страницы: 76

Бренд: Webb Страницы: 24

Бренд: Tiger Страницы: 202

Бренд: Kubota Страницы: 315

Бренд: Kubota Страницы: 24

Бренд: Husqvarna Страницы: 68

Бренд: Partner Страницы: 10

Бренд: Craftsman Страницы: 40

Бренд: Craftsman Страницы: 40

Бренд: Craftsman Страницы: 40

Бренд: Craftsman Страницы: 40

Бренд: Craftsman Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды