Jacobsen 67069 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 56

background image

6 OPERATION

18

6

OPERATION

6.1 DAILY INSPECTION________________________________________________________

1.

Perform a visual inspection of the entire unit, look for
signs of wear, loose hardware, and missing or
damaged components. Check for fuel or oil leaks to
ensure connections are tight and hoses and tubes
are in good condition.

2.

Check the fuel supply, radiator coolant level,
crankcase oil, and air cleaner indicator. All fluids
must be at the full level mark with engine cold.

3.

Make sure all mowers are adjusted to the same
cutting height.

4.

Check tires for proper inflation.

5.

Test the Interlock System.

Note:

For more detailed maintenance information,

adjustments, and maintenance/lube charts, see the

Parts & Maintenance

manual.

6.2

Operator Back-up System _________________________________________________________________

1.

The operator back-up system prevents the engine
from starting unless the parking brake is engaged,
the traction pedal is in neutral, and the reel/3WD
switch is OFF. The system also stops the engine if
the operator leaves the seat with the reel/3WD switch
ON, traction pedal out of Neutral, or parking brake
Disengaged.

2.

Perform each of the following tests to insure the
operator back-up system is functioning properly.
Stop the test and have the system inspected and
repaired if any of the tests

fail

as listed below:



the engine

does not

start in test 1;



the engine

does

start during tests 2,3 or 4;



the engine

continues

to run during tests 5 or 6.

3.

Refer to the chart below for each test and follow the
check (



) marks across the chart. Shut engine off

between each test.

Test 1:

Represents normal starting procedure. The

operator is seated, parking brake is engaged, the
operator’s feet are off the pedals, and the reel/3WD
switch is OFF. The engine should start.

Test 2:

The engine must not start if the reel/3WD

switch is ON.

Test 3:

The engine must not start if the parking brake

is DISENGAGED.

Test 4:

The engine must not start if the traction pedal

is pressed.

Test 5:

Start the engine in the normal manner then

turn reel/3WD switch ON and lift your weight off the
seat.



Test 6:

Start the engine in the normal manner then

disengage parking brake and lift your weight off the
seat.





Lift your weight off seat. The engine will shut down.

CAUTION

The daily inspection should be performed only when
the engine is off and all fluids are cold. Lower mowers
to the ground, engage the parking brake, stop engine,
and remove ignition key.

!

WARNING

Never operate equipment with the Interlock System
disconnected or malfunctioning. Do not disconnect or
bypass any switch.

!

Operator’s Back-up System Check

Test

Operator

Seated

Parking

Brake

Traction Pedal

in Neutral

Reel / 3WD

Switch

Engine

Starts

Yes

No

Engaged

Disengaged

Yes

No

On

Off

Yes No

1











2











3











4











5













6













«
...
16
17
18
19
20
...
»

Содержание 67069

























































Отзывы:

Нет отзывов

Похожие инструкции для 67069

ransomes hr3806

Бренд: Jacobsen Страницы: 172

Бренд: Jacobsen Страницы: 10

Бренд: Gardenline Страницы: 36

Бренд: MTD Страницы: 20

Бренд: Tar River Страницы: 32

Бренд: Far Tools Страницы: 21

Бренд: Sears Страницы: 32

Бренд: Cobra Страницы: 18

Бренд: Land Pride Страницы: 2

CRAFTSMAN 944.604060

Бренд: Sears Страницы: 56

sunjoe 24V-CRLM15

Бренд: SNOWJOE Страницы: 64

Бренд: Lastec Страницы: 21

Бренд: Southland Страницы: 24

Бренд: Southern States Страницы: 33

Бренд: Husqvarna Страницы: 29

Бренд: Husqvarna Страницы: 35

Бренд: Husqvarna Страницы: 28

Бренд: Husqvarna Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды