Jacobsen 67069 Скачать руководство пользователя страница 16

Страница: 16 / 56

5 CONTROLS

5.2

CONTROLS ______________________________________________________________

Throttle Lever

Used to regulate engine speed.

Glow Plug Switch

Used to energize the glow plugs (Refer to

Section

6.4

Circuit Breaker

If the gauges or ignition system fail to operate
properly, check the circuit breaker then depress cap
to reactivate the breaker.

Water Temperature

Indicates engine coolant temperature. Normal
operating temperature should be 185° - 195° F (85° -
91° C).

Engine Oil

The indicator will light if engine oil pressure drops
below 7 psi (48 kPa). Stop engine immediately,
determine the cause, and correct the problem before
resuming operation.

Voltmeter

Indicates battery condition. During normal operation
meter should never be in the red area.

Hour Meter

Used to time maintenance intervals or mowing
operations. The meter operates only when the
ignition key is in the ON position.

Ignition Switch

Used to start the engine. Remove the ignition key
when the mower is not in use.

Reel / 3WD Switch

Used to engage mowers and also select two wheel
drive or three wheel drive (2WD or 3WD).

Pull the lever upward and forward to engage

clutch and engage 3WD mode.

Push switch lever down to disengage clutch and

engage 2WD mode.

Backlap Switch

Used for maintenance only to hone the reels and
bedknife.

Note:

The switch must be in Forward Rotation for

normal operation. Always remove and store the key
after backlapping.

Parking Brake Light

Indicates that the parking brake is engaged. Parking
brake must be disengaged before depressing traction
pedal.

Lift/Lower Pedal

Used to lift or lower the implements. Depress top of
pedal (

) to lower and engage reels. Hold pedal

down, until implements are fully lowered then release
the pedal.

Push rear of pedal (

) pedal to raise and stop reels.

Hold pedal down until implements are fully raised,
then release pedal.

Traction Pedal

Used to control the direction and speed of the
machine.

Slowly depress the top of the traction pedal (

) for

forward motion or rear pedal (

) pedal for reverse.

The pedal will return to neutral when released.

Do not depress traction pedal in either direction with
parking brake light (

) on.

Parking Brake Lever

Push up and forward to engage brake. Pull back and
down to disengage brake.

Hood Latch

Used to keep hoods closed.

Left Side Hood

Used to cover the engine and radiator area. See

Section 5.3

for opening instructions.

Right Side Hood

Used to cover the traction pump and hydraulic filter
area. See

Section 5.3

for opening instructions.

Console Latches

Used to secure the console cover to the steering
tower.

Cooling Air Intake

Air is drawn through screen to provide cooling for the
engine. Keep the screen free from obstructions.

Engine Air Filter Intake

Engine intake air is drawn through screen. Keep the
area clean and the screen free from obstructions.

Cooling Air Intake

Engine Air Filter Intake

Light Switch -

(Optional Kit)

Used to turn the optional lights on and off.

Steering Console Cover

Used to cover the steering column, relays and fuses.
See

Section 5.4

for removal instructions.

Содержание 67069

























































Результаты поиска

Содержание 67069

Отзывы:

Похожие инструкции для 67069

Бренды по названию

Популярные бренды

Jacobsen 67069, Руководство по эксплуатации

Результаты поиска

Содержание 67069

Отзывы:

Похожие инструкции для 67069

Бренды по названию

Популярные бренды