IXSEA AR861B2S Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 31

background image

M U _ O C E A N O 2 5 0 0 S - U n i v e r s a l _ U K

I ss u e 10

3 0 •05 •07 28

This document is the property of IXSEA and shall not be reproduced nor transmitted without written approval

7.3.1 Transducer

cap

The transducer cap must not be greasy, clean with liquid soap to remove any grease or deposits. Do not use
alcohol or petrol-based solvents on the neoprene casing.

7.3.2 O-ring

seals

It is advised to clean the O-ring seals as well as the seal housings and to grease them with silicone before
closing the acoustic release. Replace damaged or scratched seals (Refer to § Maintenance).

7.4 STORAGE

The device must be correctly sealed and stored in a clean area. If the user wants to keep the batteries installed
during storage, it is recommended to inhibit PINGER ON function. The storage with batteries removed is the
advised storage mode for long storage periods. Refer to the previous paragraphs to open the equipment and
remove the batteries.

7.5 TROUBLESHOOTING

•

Transducer

test

•

Reception

test

•

Transmission

test

•

Battery voltage test and current measurement in stand-by/ listening mode

8. CUSTOMER SUPPORT

Customer’s technical support on this product is available:

•

by e-mail :

[email protected]

•

by phone through IXSEA 24/7 hot-line :

+33 (0)1 30 08 98 98 for EMEA

+1 781 937 8803 or +1 888 660 8836 (toll free) for US

+65 6747 7027 for Asia

Contact IXSEA support for any request on technical matters related to this product.

IXSEA customer’s support commits to provide a quick response to your query.

«
...
28
29
30
31
»

Содержание AR861B2S
































Отзывы:

Нет отзывов

Похожие инструкции для AR861B2S

Бренд: Keithley Страницы: 36

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Sagola Страницы: 8

Бренд: B&G Страницы: 3

Бренд: B-K lighting Страницы: 3

Бренд: Eaton Страницы: 16

Бренд: Eaton Страницы: 6

Бренд: Ecco Страницы: 17

COOPER POWER SERIES

Бренд: Eaton Страницы: 8

Бренд: YMC Страницы: 49

Бренд: Octane Fitness Страницы: 8

Бренд: Octane Fitness Страницы: 10

Бренд: OCENCO Страницы: 48

Бренд: Ocean Optics Страницы: 6

Бренд: S.R.Smith Страницы: 8

Бренд: S.R.Smith Страницы: 23

NavBoard ZipFlip

Бренд: S&S Precision Страницы: 6

Бренд: TEC Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды