IXSEA AR861B2S Скачать руководство пользователя страница 15

Страница: 15 / 31

M U _ O C E A N O 2 5 0 0 S - U n i v e r s a l _ U K

I ss u e 10

3 0 •05 •07 13

This document is the property of IXSEA and shall not be reproduced nor transmitted without written approval

6.1.4 Testing the Pinger Mode

Perform the procedure in 6.1.2 with the PINGER ON command.

For the PINGER ON command, the remote control unit displays the pinger rate. After reception of the second

CAF acknowledgement (which confirms the execution of the command), the settings of the pinger are

displayed on the remote control unit. The PFR receiver updates the message

RECEIVING DATA

upon

detection of the pinger frequency and returns the pinger rate measured with the message

PINGER Rate

value

in second

To switch the pinger mode off, repeat the procedure described in 6.1.2 replacing PINGER ON command by

PINGER OFF and Other CMD for the command type. The acoustic device stops the free running transmitting

mode.

6.1.5 Testing the Simple Ranging Operation

Perform the procedure above with the PINGER OFF or “ARM + ARM” command type.

The acoustic device transmits successively two CAF pulses that are received and processed by the remote

control unit. The ranging information is then displayed.

No other operation then transmitting CAF pulses is expected from the Acoustic Actuator.

6.1.6 Testing the Telemetry mode

Perform the procedure above with the TELEMETRY command type.

For TELEMETRY command, the remote control unit displays the tilt (vertical or horizontal) of the AR800 and the

indication of the battery voltage of the beacon. After reception of the second

CAF

acknowledgement (which

confirms the execution of the command), the message

WAITING FOR DIAGNOSTIC

is posted up until the

completion of the telemetry operation. The AR800 returns several acoustic pulses (Pulse to Pulse modulation)

to transmit information about voltage of the main battery pack and verticality range. Then the remote control unit

displays the status message that comprises the Tilt of beacon (

VERTICAL

HORIZONTAL

) and the battery

voltage (Vbat

value in Volt).

Note:

VERTICAL

means that the main axis of the beacon housing is vertical, with the upper Acoustic I/O end cap

looking upwards.

Содержание AR861B2S
































Результаты поиска

Содержание AR861B2S

Отзывы:

Похожие инструкции для AR861B2S

Бренды по названию

Популярные бренды

IXSEA AR861B2S, Руководство пользователя

Результаты поиска

Содержание AR861B2S

Отзывы:

Похожие инструкции для AR861B2S

Бренды по названию

Популярные бренды