manualshive.com logo in svg

ITW Simco Ion IQ Power Fantom HL, Инструкция по установке и эксплуатации

Поделиться
Скачать
ITW Simco Ion IQ Power Fantom HL Скачать руководство пользователя страница 9

7

IQ Power Fantom HL

5201305 Rev A

Figure 2.  Conduit Seal on 8 Conductor Modular and HV Cables

System Wiring 

Termination of HV Cable

Connect static bar by cutting high voltage cable to length, terminating leads, and 

connecting to power supply: (see Figure 3) 

1.   Cut HV cable to length, leaving an extra 3¼” for connector. 
2.   Strip black plastic jacket back 2½”, being careful not to nick insulation of HV 

wires. (Practice stripping jacket on waste length of HV cable.) 

3.   Strip insulation of HV wires back 1”, being careful not to nick conductor of HV 

wire. 

4.   Straighten conductors and insert into HV connector until conductor protrudes 

out from the tip of connector. 

5.   Solder conductor to tip of connector by applying solder to exposed conductor. 

Ensure that the solder does not overflow and fill neck area of tip. 

6.   Trim off excess conductor protruding from tip of connector. If using the HLC 

power supply, the HV cable is now ready to use. If using the HL power supply, 

continue to step 7.

Содержание Simco Ion IQ Power Fantom HL

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды