manualshive.com logo in svg

ITW Simco Ion IQ Power Fantom HL, Инструкция по установке и эксплуатации

Поделиться
Скачать
ITW Simco Ion IQ Power Fantom HL Скачать руководство пользователя страница 21

19

IQ Power Fantom HL

5201305 Rev A

Bar Type

: A fixed description for the type of bar connected to the HL power supply 

(speed). 

Bar HV

: Allows turning internal HV power supplies on / off. 

Ion Output

: Displays the ionization level, in percent, where Bar Calibration = 

100% and the ionization level in terms of microamps for both positive and negative 

ionization. 

Balance

: A ratio of input power supplied to the high voltage power supplies that is 

related to ion balance. In Fixed, Auto-Tune and CLFB modes this is a display only 

and non-editable. The Balance may only be user adjusted in the Manual mode. 

Operation Mode

: A user selectable operating mode for the static bar (Manual, 

Fixed, Auto-Tune, CLFB). 

•  

Fixed

 – 50/50 balance standard operation (default factory setting). Fixed 

provides standard operation, with output voltage regulation. 

•  

Auto-Tune

 – This mode is not recommended for use with the Fantom HL 

blower. 

•  

CLFB (Closed-Loop Feedback) 

– The best control of ion balance. The 

IQ Power HL Sensor connected to an HL power supply will automatically 

pair with that power supply for closed-loop control. The sensor must be 

positioned to detect static at the target of neutralization in order for CLFB 

to work. The sensor detects any charge imbalance at the target, or material 

to be neutralized, then transmits this information to the static neutralizing 

power supply. The power supply makes incremental changes to the balance 

setting until target charges are minimized. 

•  

Manual

 – Allows manual control of the ion balance. Manual mode includes 

voltage regulation and current monitoring found in the standard mode, plus 

manual control of the ion balance ratio. This mode of operation would only 

be selected where the web, or material to be neutralized, exhibited extreme 

and consistent charging of one polarity.

Mounting Distance

: A user entered value used only in the Auto-Tune mode. Not 

recommended for use with the Fantom HL blower. 

Web Speed

: A user entered value used only in the Auto-Tune mode. Not 

recommended for use with the Fantom HL blower.

Device Address

: The Power Supply Number (address / device number) assigned to 

the HL power supply. The address may be edited, but duplicate address numbers 

are not permitted. The exception to this rule is static sensors. When a static Sensor 

Interface is connected to an HL power supply (PS COMM 2) the Sensor Interface 

will automatically be assigned the same address number as the HL power supply. On 

the Control Station, the data from Sensors connected to that Sensor Interface will 

appear as a tab under the HL power supply and the interface will automatically be 

paired with that HL power supply for CLFB operation. 

Содержание Simco Ion IQ Power Fantom HL

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды