ITW Simco Ion IQ Power Fantom HL Скачать руководство пользователя страница 30

Страница: 30 / 32

IQ Power Fantom HL

5201305 Rev A

8. PARTS AND ACCESSORIES

Part Description

Part No.

Fantom HL Blower (115 VAC input)

4017126

IQ Power HL Power Supply (no AC adapter)

4012508

IQ Power HL Power Supply (with AC adapter, 100/120 VAC Japan / North America Cord)

4012509

Replacement Power Unit for IQ Power HLC SPEED (for use with HL Speed Bars only)

4110350

IQ Power HL Speed-T Bar (for Fantom HL Blower)

4015798

AC Adapter (100-240 VAC input, 24 VDC, 1.6A max output)

4108104

Line Cord, 100/120 VAC Japan/ North America

4106272

Air Filter Replacement Kit (20 Filters)

4100642

Ground Lead (90” with ring terminals)

4108926

DB25 Connector (for Alarm Output)

4612203

DB25 Back Shell (for Alarm Output)

4612204

Modular Cable (RJ-45 to RJ-45, IQ Power 8-conductor, crossover wired)

for use between Control Station and IQ Power HL/HLC (Ref. Figure 10 & 11)

DO NOT USE Standard Ethernet Cables

0.91 meter [3 foot] black

2.13 meter [7 foot] black

4.27 meter [14 foot] black

7.62 meter [25 foot] black

15.24 meter [50 foot] black

30.48 meter [100 foot] black

4520785

4520786

4520787

4520784

4520844

4520845

HL Junction Block

4012352

HL Conduit Seal

4108231

Содержание Simco Ion IQ Power Fantom HL

































Результаты поиска

Содержание Simco Ion IQ Power Fantom HL

Отзывы:

Похожие инструкции для Simco Ion IQ Power Fantom HL

Бренды по названию

Популярные бренды

ITW Simco Ion IQ Power Fantom HL, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Simco Ion IQ Power Fantom HL

Отзывы:

Похожие инструкции для Simco Ion IQ Power Fantom HL

Бренды по названию

Популярные бренды