iSys iTerra Elite Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 119

background image

_________________________________________________________________________________________________________________________

PAGE 25

---

iTerra Elite

Quick Start Guide

© 2008 iSys-The Imaging Systems Group Inc.

III.

NETWORK INSTALLATION

C. Network Port Connection

1)

Turn the printer off.

2)

Connect your Ethernet cable to the network port on the printer (1).

3)

Connect the other end of the Ethernet cable to the network port, Hub or host system (2).

4)

Turn the printer on and wait for the print server status light (3) to stop blinking.

If you are unaware of what the network IP set value is for the printer, follow the instructions below to determine that value.
You will need to know the printer IP before you can load the printer driver.

If a network configuration card is not already installed refer to Trouble Shooting Chapter and/or Accessory installation (if
network card is purchased later than printer).

NOTE:

Ethernet® cable is not supplied with the printer. Use an Ethernet cable with two twisted wire pairs and an
RJ45 plug.

«
...
23
24
25
26
27
...
»

Содержание iTerra Elite
























































































































Отзывы:

Нет отзывов

Похожие инструкции для iTerra Elite

Бренд: TDT Страницы: 15

Бренд: B3 innovations Страницы: 12

Perfecta 3600STP

Бренд: Variquest Страницы: 12

Perfecta 3600STP

Бренд: Variquest Страницы: 231

Awards Maker 400

Бренд: Variquest Страницы: 4

Бренд: Xerox Страницы: 55

Бренд: Axis Страницы: 10

Бренд: Xerox Страницы: 13

Бренд: Rena Страницы: 59

Бренд: Sagem Страницы: 102

Бренд: Minolta Страницы: 227

Бренд: Oki Страницы: 109

RepRap Industrial

Бренд: Kuhling&Kuhling Страницы: 24

Бренд: Kyocera Страницы: 2

Бренд: Paaasonic Страницы: 14

Бренд: CognitiveTPG Страницы: 2

Бренд: Kyocera Страницы: 72

DocuPrint 4635 IPS Series

Бренд: Xerox Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды