ISA T2000 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 110

background image

DOC. MIE11110 Rev. 5

Page 49 of 110

B) Input connection:
- N. 1 cable for low voltage measurement connection, shielded, 4
m long, for the 10 V measurement, plus N. 2 Clamps to connect
the voltage measurement.

Prior to the test, you can select if the test result has to be
compensated taking into account the temperature, and computed
to a reference temperature (as specified for the CT). Once
enabled the compensation, the operator:
. Selects the temperature scale, °C or °F;
. Inputs the ambient temp erature, as measured on the CT;
. Inputs the reference temperature at which the resistance will be
reported.

Press test start button (56), and adjust the test current to the
desired value by the adjustment knob (6): the screen shows:
. The test current;
. The corresponding voltage drop;
. The ohm burden at the ambient temperature;
. The ohm burden at reference temperature.
These measurements will not change very much with the test
current.

When you are satisfied with the result, press SAVE: test result is
saved. Return to zero the adjustment knob (6).

VERY IMPORTANT NOTICE

: during the current adjustment, a

current is induced into the primary loop, that is short-circuited:
the induced current is a function of the current rate of change.
For this reason, the test current MUST BE INCREASED VERY
SLOWLY: the current is delayed with respect to the voltage.
When the desired test current is reached, it is necessary to wait
for a while until it stabilizes. After SAVE, DECREASE THE CURRENT
VERY SLOWLY TO ZERO. The time should be not less then 10 s for
increasing and reducing the current.

If you press STOP when the adjustment knob is not at zero, the
following message is displayed, AND THE CURRENT IS NOT
REMOVED:

«
...
47
48
49
50
51
...
»

Содержание T2000















































































































Отзывы:

Нет отзывов

Похожие инструкции для T2000

Бренд: ABB Страницы: 50

ACS880-01 Series

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 36

Бренд: Keithley Страницы: 149

Бренд: XAG Страницы: 24

Бренд: ADVANCED HOME CARE Страницы: 16

Бренд: xsto Страницы: 76

Бренд: F&V Страницы: 5

Бренд: F Care Systems Страницы: 2

Бренд: ParaBody Страницы: 5

Бренд: Hammer Strength Страницы: 18

Бренд: unios Страницы: 2

ActiveFinder One

Бренд: LaserLiner Страницы: 92

Бренд: NatureZap Страницы: 2

ProFire Lightbridge

Бренд: M-Audio Страницы: 8

Бренд: M-Audio Страницы: 36

Бренд: Carbatec Страницы: 29

Бренд: PurAthletics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды