ISA T2000 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 110

background image

DOC. MIE11110 Rev. 5

Page 18 of 110

A) Output connection, 800 A:
- N. 2 High current connection cables, 100 sq. mm, 4 m long.
Terminated on one side with the high current connector; on the
other side, it is possible to use one of the following three
connections.
. The male to male jumper, that allows closing the cable loop into
the hole of the current transformer.
. The high current clamp, that eases the connection to the bars,
but has a maximum current rating of 400 A.

Do not go beyond

this value, as the heat can damage the clamp

!

. The high current vice, that is a bit less easy to use than the
clamp, but that allows testing up to the maximum current rating.
However, with tests at 800 A, the burden of the 4 m cables can
impeach to reach this current. If the test current is not the
desired one, use the 1 m connection cables provided.

B) Input connection:
-  N. 2 measurement cables, for the secondary current, plus N. 2
Clamps. In alternative, if desired: N. 1 Clip-on transformer, plus N.
2 measurement cables (to the clip-on transformer).
-  N. 2 measurement cables (to the 600 V measurement), or N. 1
cable for low voltage measurement connection, shielded, 4 m long
(for the 10 V measurement; shown in the circuit diagram), plus N.
2 Clamps to connect the voltage measurement.

Primary clamps shall be well tightened on a clean surface, so that
contact resistance is negligible.

For secondary  connection, it is possible to decide whether to
measure the secondary current by opening the circuit or by means
of the optional clip-on current transformer; to this purpose, the
clip-on transformer is more easily used, but it looses accuracy.

Secondary  leads should be twisted to reduce stray flux influence.
Take care of current direction, else the polarity test will give
wrong result: the red socket (output or input) is the positive; with
the clip-on transformer, look at the arrow or at the red mark
(entering current).

Also for the measurement of the voltage you have to take care of
the polarity. You can use either the 10 V metering input or the

«
...
16
17
18
19
20
...
»

Содержание T2000















































































































Отзывы:

Нет отзывов

Похожие инструкции для T2000

Бренд: FENDT Страницы: 31

Бренд: Panlux Страницы: 2

Бренд: Echo Страницы: 6

Pro Attachment Series

Бренд: Echo Страницы: 28

Бренд: Echo Страницы: 2

Pro Vantage 12+ Series

Бренд: Ecco Страницы: 6

Бренд: Nautilus Страницы: 17

Бренд: National Instruments Страницы: 6

Бренд: Pari Страницы: 11

Бренд: Pari Страницы: 2

Бренд: Haas Страницы: 5

Бренд: Ultrasonic Страницы: 33

Бренд: DAAB Страницы: 12

Бренд: ebm-papst Страницы: 10

CEAG Exit Cube 33822 LED CGLine+

Бренд: Eaton Страницы: 20

Бренд: swamp Страницы: 5

Бренд: Mindray Страницы: 295

Бренд: ZAMST Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды