IPM balancedpower plus Скачать руководство пользователя

Страница: 63 / 99

SECTION III

Operation

Page 3.32

BP+2.9X
11/95

3.6 UPS Operating Procedures (continued)

3.6.3

UPS Maintenance Menu (continued)

3.6.3.3

SBS Maintenance Menu (continued)

15. If it is desired to manually retransfer

to primary UPS input, press

and wait 10

seconds for this screen to appear. This will turn
off all the LED’s except

UPS Normal.

16. Normally, the system will be left so

that transfer and retransfer are enabled.
Following Step 11 of this subsection press
once or twice to obtain this screen with either
“transfers” or “retransfers” on the top line.
Pressing

will change between “enabled”

and “disabled” on the bottom line.

17. Press to obtain –

18. Press

to return to the SBS

Maintenance Menu.

3.6.3.4

System Maintenance Menu

1. Press to advance to the System

Maintenance Menu.

Man Transfer

/Retransfer

Inv Running

Retransfers

Enabled

Return to

SBS

Maintenance

System

Maintenance

Содержание balancedpower plus




































































































Результаты поиска

Содержание balancedpower plus

Отзывы:

Похожие инструкции для balancedpower plus

Бренды по названию

Популярные бренды

IPM balancedpower plus, Инструкция по установке и эксплуатации

Результаты поиска

Содержание balancedpower plus

Отзывы:

Похожие инструкции для balancedpower plus

Бренды по названию

Популярные бренды