background image

                                                                                                            Ytterbium Fiber Laser, Model YLR-200-AC

 

                                                                                                      

IPG Laser GmbH, 2009                                                                                           

 

Proprietary Information. All rights reserved 

Rev. Date 08-12-2009 

 

4

 

Table of Contents

 

 
 
 
 

 

1.

 

General Safety Information .................................................................................................................... 5

 

2.

 

Description ............................................................................................................................................. 9

 

3.

 

Accessories.......................................................................................................................................... 10

 

4.

 

Environmental Conditions and Precautions ......................................................................................... 11

 

5.

 

Front and Rear Panel Description ....................................................................................................... 16

 

6.

 

Operation. ............................................................................................................................................ 19

 

7.

 

Warranty .............................................................................................................................................. 28

 

8.

 

Instruction for product returns .............................................................................................................. 31

 

9.

 

Unpacking and Inspection ................................................................................................................... 32

 

 

Содержание YLR-200-AC

































Отзывы: