English
- 13 -
stability.
- Connect a 5/8 inch ID or larger garden hose to the supply water
connection fitting. Use of more than 100 ft of garden hose may
affect system performance.
- Connect the male end of the garden hose to the INLET port
on the equipment.
- Position the WASTEWATER hose outlet to landscape or other
area to accept the concentrate water flow. Additional garden
hoses may be added if required to reach designated area.
- Connect the PURE WATER hose to the fitting on the end, in
the center of the cap.
- Connect the other end of the PURE WATER hose to the water-
fed pole hose. A control valve is typically installed between these
two hoses for operator control. (Fig. 2-2A)
Electrical connection (Vers. E).
Warning
The equipment should be connected to the mains in accordance
with current legislation.
Make sure the mains voltage corresponds to the voltage
required by the appliance and indicated on the ratings plate.
Protect the electric cable from accidental crushing.
Failure to respect the above conditions absolves the
manufacturer from all liability and represents negligent
use of the product.
Protection against accidental contact.
Before removing the panels, unplug the appliance from the
mains. Before using the appliance, make sure the panels are
correctly assembled and fixed.
Failure to respect these instructions could result in electric
shock and absolves the manufacturer from all liability.
RECOMMENDATIONS FOR USE
Cleaning of covered and painted surfaces.
The use of pure water on glued surfaces could cause detach-
ment. Do not use the appliance on parquet or wooden floor that
are not well sealed.
Pay the utmost attention when cleaning covered and painted
doors, parquet, aluminium panels and surfaces in general.
Before using pure water, we suggest to test a corner of the
surface, in order to avoid damage during cleaning.
Window cleaning.
Do not lead the stream of water directly on the sealed area of
the window, so not to damage the sealed corners.
USING THE EQUIPMENT
Starting the Equipment:
- Turn water supply valve to its full open position.
- Verify water flow at the WASTEWATER outlet.
Equipment with Pump Unit.
- Turn motor switch ON by pressing the push button.
- Allow PURE WATER to flow from brush for 1 - 2 minutes.
- Take a sample of the PURE WATER at the brush and test it
with the TDS meter. If water test is higher than 10 ppm, service
of Equipment is required.
- Wash windows as directed. Adhere to safety precautions for
use as recommended by pole manufacturer.
The leftover water now has higher TDS level than when it ente-
red the system and is called concentrate. It exits the membrane,
flows around the outside of the DI cartridge and out through
the side port marked waste water. There is an automatic flow
regulator installed in the waste water outlet fitting which con-
trols the waste water flow rate to maintain the proper balance
of the entire system. Concentrate water discharge flow can be
directed safely to any landscape vegetation, to a sanitary or
storm sewer drain.
The unit must be protected from freezing.
PRELIMINARY OPERATIONS
Unpacking:
After unpacking the appliance, check it is complete and un-
damaged.
If in doubt, do not use the equipment. Contact your dealer.
Packaging (bags, boxes, nails etc) should be kept out of reach
of children as they may represent a potential hazard. They
should be disposed of or kept according to national environ-
mental legislation.
Assembling parts supplied separately.
All main parts and safety devices are assembled by the
manufacturer. Some other secondary parts may be supplied
separately.
These parts must be assembled by the user following the as-
sembly instructions.
The pre-filter, RO membrane and DI resin cartridge are already
installed inside the Appliance.
Identification plate:
Warning
When purchasing the product, make sure it has an identification
plate. If this is missing, notify the manufacturer and/or dealer
immediately.
Use of an appliance without an identification plate absolves the
manufacturer from all liability. Products without an identifica-
tion plate should be considered as anonymous and potentially
dangerous.
The main technical characteristics of the equipment are given
on a plate applied on the back of the appliance.
The user must ensure that the rooms where the equipment is
to be used comply with all safety standards and regulations
regarding:
- efficient electrical installations;
- the absence of explosive, inflammable, toxic or corrosive
substances.
Use of the appliance in particular conditions requiring use of
class II appliances only is not recommended.
Hose assembly
:
Attach the wastewater discharge hose to the wastewater outlet
port on the side of the tube near the handle.
The equipment is now ready for use. (Fig. 1)
Water circuit connection and accessories:
- Locate supply water connection at job site.
- Find suitable setup location for appliance at the job site.
- Lay equipment down in a horizontal position for maximum
!
!
Содержание APTA40008
Страница 22: ......
