manualshive.com logo in svg

Invacare Spectra XTR, Руководство по обслуживанию, Страница: 41 / 48

Поделиться
Скачать
Invacare Spectra XTR Скачать руководство пользователя страница 41

Service

6.

Remove both battery boxes (see

5.11.1 Removing

Battery Boxes, page 36

).

7.

Remove front headlight plug from lighting PCB.

8.

Free cable or remove any cable ties.

9.

Loosen nut (2) with a 7 mm jaw spanner and a 3
mm Allen key.

10. Remove front headlight (1) from lamp holder (3).
11. Install parts in reverse order.
12. Test all functions.

5.12.2 Replacing Front Lamp Holder (LED Light)

•

7 mm wrench

•

3 mm Allen key

•

TX25 screwdriver

•

Oblique pliers

•

Tie wraps

1.

Fig. 5-71

Loosen nut (2) and remove.

2.

Remove front headlight (1) from lamp holder (3) and
place it carefully to the side.

3.

Fig. 5-72

Undo and remove screws (4) with a TX25 screwdriver.

4.

Replace lamp holder (3).

5.

Install parts in reverse order.

6.

To complete, check all vehicle functions.

5.12.3 Replacing Rear Light (LED Light)

Replacing an individual LED is not possible. If there
is a defect, replace the entire rear light.

•

Phillips screwdriver

•

TX40 Torx key

•

Oblique pliers

•

Tie wrap

1.

For plug position, see corresponding controls manual
or earlier revision of this manual.

2.

Remove legrests.

3.

Fig. 5-73

Release seat

A

and tilt forwards.

4.

Disconnect remote bus cable from power module or
ACT.

5.

Lift seat out of the front anchorage and remove it. The
seat has a heavy weight. Use proper lifting techniques.

6.

Remove both battery (see

5.11.1 Removing Battery

Boxes, page 36

)

7.

Remove drive wheel (see

Replacing Drive Wheel

(5–Screw Installation)

).

8.

Fig. 5-74

Remove rear light plug from lighting PCB.

9.

Free cable or remove any cable ties.

10. Undo Phillips screw (1) and remove it together with

washer.

11. Remove rear light (1) from fender and replace it.
12. Install parts in reverse order.
13. To complete, check all vehicle functions.

5.13 Seating

•

This manual refers to configurations with Modulite
seat system. Older specifications (for example Flex2
seat system) have been described in revision 15 of
this service manual.

•

For seat systems, refer to the corresponding manual.

5.13.1 Replacing Tilt Tube

CAUTION!
Risk of Crushing to Hands and Feet by Weight
of Seat

– Pay attention to hand and feet.
– Use proper lifting techniques.

•

Flat screwdriver

•

Oblique pliers

•

Tie wraps

1528338-Q

41

Содержание Spectra XTR

















































Отзывы:

Нет отзывов