Invacare Spectra XTR Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 48

Invacare Spectra XTR Скачать руководство пользователя страница 13

5 Service

5.1 General Warning Information on
Installation Work

CAUTION!
Risk of damage to vehicle

Collisions can be caused if the adjusting washers
are removed during fitting work to the drive
wheels. Adjusting washers are often fitted
between the drive shaft and the wheel hub to
even out tolerances. If these adjusting washers
are removed and not replaced again, collisions
can be caused.

– Always replace the adjusting washers exactly

as they were before you started dismantling.

CAUTION!
Risk of injury and damage to property, if
the maximum speed reduction on a mobility
device with a lifter does not function correctly

The mobility device’s control unit must reduce
the maximum possible speed as soon as the
lifter is raised.

– Test the maximum speed reduction for

correct function after any maintenance work
or modifications to the mobility device.

5.2 Troubleshooting

5.2.1 Operational Faults

Proceed as follows if you have any problems:

1.

First assess the possible cause of the problem using
the following table.

2.

Check the remote status display. Evaluate the flash
error code.

3.

Carry out the necessary checks and repairs as
recommended in the following table.

The various power modules can be fitted in connection
with different remotes in the mobility device. Rectification
of operational faults depends on the power module
fitted. The power modules used are described in the
corresponding controls manual.

The tables for rectification of operational faults
listed in the following chapters are only an excerpt
from the original manufacturer's manuals. You can
obtain the original manuals from Invacare.

5.2.2 Drive Fault Diagnosis

Problem

Other symptoms

Possible cause

Solution

Documentation

The remote status
display illuminates
normally and shows
an error code.

Drive motors
disengaged

Engage drive motors

See corresponding
remote manual

Batteries defective

Replace batteries

See

5.11 Batteries,

Completely discharge
battery

Pre-charge batteries

See user manual

Power supply to
remote interrupted

Check main fuse

See

5.11.6 Main Fuse,

Remote status display
does not illuminate

Remote defective

Check cables between
the modules for
loose connections and
damage

See

5.11.7 Checking

Cables, page 40

Mobility device will
not start

Remote status display
blinking

Various causes

Assess error code

See corresponding
remote manual

Batteries defective
(unstable voltage)

Replace batteries

See

5.11 Batteries,

Replace motor(s)

See

Components, page
18

Mobility device
judders in drive mode

None

Drive motor(s)
defective

Replace carbon
brushes

None

Batteries defective

Replace batteries

See

5.11 Batteries,

Batteries not being
charged

LEDs blinking on
charging unit

Charging unit defective

Replace charging unit

See user manual

1528338-Q

13

«
...
11
12
13
14
15
...
»

Содержание Spectra XTR

















































Отзывы:

Нет отзывов