Invacare Spectra XTR Скачать руководство пользователя страница 14

Страница: 14 / 48

Invacare® Bora® / Spectra® XTR Series

Problem

Other symptoms

Possible cause

Solution

Documentation

Remote defective

Replace remote

See corresponding
electronics manual

Mobility device runs
too slowly

None

Batteries defective

Replace batteries

See

5.11 Batteries,

page 35

5.3 Tightening Torques

CAUTION!
Risk of damage to mobility device due to
improperly tightened screws, nuts or plastic
connections.

– Always tighten screws, nuts etc. to the stated

tightening torque.

– Only tighten screws or nuts which are not

listed here fingertight.

The tightening torques stated in the following list are
based on the thread diameter for the nuts and bolts for
which no specific values have been determined. All values
assume dry and de-greased threads.

Thread

Tightening Torque in

Nm ±10 %

3 Nm

6 Nm

10 Nm

25 Nm

M10

49 Nm

M12

80 Nm

M14

120 Nm

M16

180 Nm

5.4 Service Plan (Once a Year)

CAUTION!
Risk of injury and damage to property, if the maximum speed reduction on a mobility device with a lifter does
not function correctly

The mobility device’s control unit must reduce the maximum possible speed as soon as the lifter is raised.

– Test the maximum speed reduction for correct function after any maintenance work or modifications

to the mobility device.

Component

Check

Remedy

Notes

Risk of damage to
armrests

Replace shrouds, if
damaged

Armrests

Armrest fixings

Tighten screws

Risk of damage to
clothes-guards

Replace clothes-guards, if
damaged

Clothes-guard

Clothes-guard fixings

Tighten screws

Seat lock

Seat lock defective

Replace seat lock

Tilt

Check SL retainer clip for
correct fit

Replace SL retainer clip, if
necessary

Risk of damage to backrest

Seams

Fixing

Check cable

Power recline (if fitted)

Check function

Replace parts, if damaged

Tighten screws

Replace actuator cable, if
necessary

Tighten screws

Frames (chassis) / battery
mounting

Check fixings, welded
seams and battery
mounting

Replace components, if
necessary

1528338-Q

Содержание Spectra XTR

















































Результаты поиска

Содержание Spectra XTR

Отзывы:

Invacare Spectra XTR, Руководство по обслуживанию, Страница: 14 / 48

Результаты поиска

Содержание Spectra XTR

Отзывы: