manualshive.com logo in svg

Invacare Spectra XTR, Руководство по обслуживанию, Страница: 40 / 48

Поделиться
Скачать
Invacare Spectra XTR Скачать руководство пользователя страница 40

Invacare® Bora® / Spectra® XTR Series

5.

Main fuse may only be replaced once fault has been
rectified.

Older fuse holder versions may be locked with
a cable tie. If so, cut open cable tie to access
fuse strip.

6.

Fig. 5-68

Remove strip fuse nuts (2).

7.

Remove strip fuse.

Installing Main Fuse

1.

Replace strip fuse.

2.

Install parts in reverse order.

Make sure to press two parts of fuse holder
shroud together until it snaps.

If older fuse holder version is used, lock fuse
holder with UL94V0 cable tie.

3.

Test all functions.

5.11.7 Checking Cables

The following images show checking the cables using
LiNX electronics as an example. The plug positions are
different for DX2 and VR2 electronics but the procedure
for checking is identical.

For plug position, see corresponding electronics manual or
earlier revision of this manual.

1.

Remove legrests.

2.

Fig. 5-69

Release seat

A

and tilt forwards.

3.

Check all cables for visible damage, crushing points
or abrasion points.

4.

Replace damaged cables.

5.

Fig. 5-70

Pull on each plug

A

carefully.

The plug must not come out of its socket when pulled
on lightly.

6.

If plug is loose, press plug into socket with slight
pressure.
The plug must snap in place securely.

7.

Check that plug is firmly attached to its socket.

8.

Remove both battery boxes. See

5.11.1 “Removing

battery boxes”, page 36

.

Remove shrouds on both battery boxes. See

5.11.2

Replacing Batteries, page 36

.

If mobility device is not fitted with battery boxes,
access batteries. See

5.11.3 Removing Batteries from

Battery Tray, page 37

.

9.

Check all battery cables for visible damage, crushing
points or abrasion points. Replace damaged cables.

10. Install parts in reverse order.
11. Test all functions.

For details on cable routing, see LiNX service
manual.

5.12 Lighting Unit

5.12.1 Replacing headlight (LED light)

Replacing an individual LED is not possible. If there
is a defect, replace the entire front headlight.

Tools:

•

7 mm jaw spanner

•

3 mm Allen key

•

Oblique pliers

•

Cable binder

1.

For position of the plugs see corresponding controls
manual or earlier revision of this manual.

2.

Remove legrests.

3.

Release seat

A

and tilt forwards.

4.

Disconnect remote bus cable from power module or
ACT.

5.

Lift seat out of the front anchorage and remove it. The
seat has a heavy weight. Use proper lifting techniques.

40

1528338-Q

Содержание Spectra XTR

















































Отзывы:

Нет отзывов