manualshive.com logo in svg

Invacare Spectra XTR, Руководство по обслуживанию, Страница: 23 / 48

Поделиться
Скачать
Invacare Spectra XTR Скачать руководство пользователя страница 23

Service

3.

Fig. 5-17

Check that screw joint (4) is positioned precisely in
engaging turn knob.

4.

Place nonwoven fabric (3) in engaging turn knob (rear
side (1)).

5.

Fig. 5-18

When installing engaging turn knob (5) make sure that
position (6) is correct.

6.

Fig. 5-19

Tighten bolt (7).

7.

Fig. 5-20

Check that engaging turn knob can be turned to
"push" position (clockwise) and "drive" position
(counterclockwise).

5.8 Wheels

5.8.1 Tyre Pressure

CAUTION!
Risk of damage to rim and tyre when tyre
pressure is exceeded

– Observe recommended tyre pressure.

For recommended tyre pressure see inscription on tyre,
rim, or contact Invacare. Compare table below for
conversion.

psi

bar

22

1.5

23

1.6

25

1.7

26

1.8

28

1.9

29

2.0

30

2.1

32

2.2

33

2.3

35

2.4

36

2.5

38

2.6

39

2.7

41

2.8

42

2.9

44

3.0

5.8.2 Tyre Types

There are three different types of tyres or inner tubes,
and specific points must be observed for the replacement
of each type. The individual types of tyres can be easily
distinguished:

•

Pneumatic tyres have black valve caps.

•

Puncture-protected tyres have red valve caps.

•

Puncture-proof tyres have no valves.

There are five chapters about tyre repair and wheel
replacement:

•

Replacing Drive Wheel (5–Screw Installation)

•

5.8.5 Replacing Drive Wheel (1-Bolt Installation), page
26

•

5.8.7 Replacing Castor Wheel on Double-Sided Fork,
page 27

•

Replacing Castor Wheels on Single-Sided Fork

•

5.8.8 Replacing Tyres, page 28

deals with tube repair

and replacing solid tyres.

Not all chapters are necessarily contained in this
manual.

Specific tightening torques for wheels and rim
halves are listed in

5.8.3 Specific Tightening

Torques, page 24

.

1528338-Q

23

Содержание Spectra XTR

















































Отзывы:

Нет отзывов