manualshive.com logo in svg

Invacare Spectra XTR, Руководство по обслуживанию, Страница: 10 / 48

Поделиться
Скачать
Invacare Spectra XTR Скачать руководство пользователя страница 10

Invacare® Bora® / Spectra® XTR Series

Fig. 4-6

1.

Remove seat plate or sling seat (1). See Modulite
service manual, “Adjusting seat width/backrest width”
chapter.

2.

Loosen screws (2) in front and rear, left and right –
DO NOT remove.

3.

Shift position of seat.

4.

Re-tighten screws.

5.

Install seat plate or sling seat.

One-Piece Seat Plate

•

6 mm Allen key

Fig. 4-7 This picture is an example.

1.

Remove seat plate (1) or sling seat. See Modulite
service manual, “Adjusting seat width/backrest width”
chapter.

2.

Loosen Allen screws (2) in front and rear, left and right
– DO NOT remove.

3.

Shift position of seat frame.

4.

Re-tighten screws.

5.

Install seat plate again.

Mounting Position of Seat Frame

The centre of gravity of the seat can be adjusted by
mounting the seat frame farther towards the front or the
rear on the seat support. See Modulite service manual.
If the mobility device is used with drive lock-out, choose
different screw positions, for example:

Fig. 4-8 Mounting Position of Seat Frame with Flex3 Backrest and

Seat Depth 51 cm

Fig. 4-9 Mounting Position of Seat Frame on Seat Support Without

Drive Lock-Out

Seat Depth Setting

Adjust the seat depth using the profile scale (1) in accordance with the following table:

Fig. 4-10

10

1528338-Q

Содержание Spectra XTR

















































Отзывы:

Нет отзывов