Invacare Spectra XTR Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 48

Invacare Spectra XTR Скачать руководство пользователя страница 16

Invacare® Bora® / Spectra® XTR Series

Component

Check

Remedy

Notes

Power supply

Check connecting plugs
for tight fit, replace, if
necessary

Drive program

Check drive program
version

Update software, if newer
version available

See LiNX manual or
revision 15 of this service
manual

Screws

Check screws for tight fit

Tighten screws, if
necessary

5.5 Overview Components

5.5.1 Mobility Device With Detachable Seat

Underneath Seat

A

Seat disengager

B

Power module / Lighting PCB (optional) / Actuator
module (optional)

Tilt

C

Tilt tube / Tilt spindle / Tilt actuator

G-Trac Sensor (Optional)

E

G-Trac sensor

The G-Trac sensor is located in the front, next to the
battery connector.

Operation Hour Counter (Optional)

F

Operation hour counter

The operation hour counter is mounted laterally on the
frame.

5.5.2 Mobility Device With Lifter And Tilt

Module

Electronic Modules

The modules are located in the front, next to the battery
connector.

16

1528338-Q

«
...
14
15
16
17
18
...
»

Содержание Spectra XTR

















































Отзывы:

Нет отзывов