Intermec Transaction Manager 9560, Руководство пользователя

Страница: 306 / 309

9560 Transaction Manager User’s Manual
I-10
Review command, 5-15, 8-29
Right Host Message command, 8-29
roadmap, 1-3
Ro-maji characters, 5-25, 5-29, 5-30
Ro-maji spelling, 5-29, 5-30
routing cables, 3-5, 3-14
routing wires, 3-14
RS-232, 1-7, 2-10
RS-422, 1-7, 2-10
RS-485 Multi-Drop, 1-7, 2-10, 2-16
RUN, 6-9, 7-31, G-8, G-15
RUN (IRL) command, 7-31
Run IRL Program command, 9-7
Run Program command, 8-30
RX EOM1, G-15
RX EOM2, G-15
S
safety summary, xv
sample IRL program
Sample 1, 9-10
Sample 2, 9-11
Sample 3, 9-14
Save Cursor Position, 5-14
Scanner Operation command, 7-47
scanner timeout, G-16
Scanner Timeout command, 7-46
scanning a label, 4-9
scanning beam, 4-6
secured wiring, 2-5, 3-5, 3-6
security plate, 3-3
SEL, 6-8
SEL command, 7-48
Select character, 7-4, G-16
Select Character Set command, 5-14
Select command, 7-48
Select event, 5-5
Select Terminal Mode command, 7-49
sense inputs, 1-5
component locations, 3-8
connecting, 3-9, 3-10
description, 2-7
sample application, 2-8
status, 2-8
typical application, 3-10
voltage levels, 3-10
sense outputs
component locations, 3-8
slot scanner, 1-6, 4-6
bar code requirements, 4-6
slot scanner, proper scanning, 4-6
solicited
protocol, 5-7
solicited protocol, 5-7
SOM, 5-8, 5-10, 6-8, G-16
SOM command, 7-50
SOP, 6-8, G-16
SOP command, 7-32
speaker, 2-9
external, 1-7
internal, A-4
special terms, xviii
specifications, A-3
physical, A-3
standard display, 5-12
Start of Message, G-16
Start of Message character, 5-8, 5-10
Start of Message command, 7-50
Start of Program Block command, 7-32
Start of Program character, G-16
starting the 9560, 4-3, 4-4
status, sense inputs, 2-8
status beeps, 1-7, 4-3, 10-5
Stop Bits command, 7-51
supported bar codes and symbologies, 6-3, A-3
symbologies, G-17
symbology, 6-3
Symbols, ASCII, B-5
synchronous
transmission, 5-4
system unit, 2-14
T
temperature range, A-4
terminal
block operation, 5-18
buffered, 5-15
full-duplex, 5-17
nonbuffered
full-duplex, 5-15, 5-18
half-duplex, 5-15, 5-18
transparent, 5-15, 5-17
terminal block, 3-10, 3-11
location, 3-8, 3-10
terminal connector, 2-13
terminal connector pin assignments, 2-12
terminal display, 5-15
Terminal mode,
Select command, 7-49
terminal operation, 5-15
terminal pin connector, 2-12
terminal plug, 2-6
terms and conventions, xviii
Time in Seconds command, 7-53
timeout, 2-7, 7-54
timeout delay, 5-9
Timeout Delay command, 7-54
Transmit command, 8-30
Transmit End of Message First character, G-17
Transmit End of Message Second character, G-17