Intermec Transaction Manager 9560, Руководство пользователя

Страница: 305 / 309

Index
I-9
I
output relays, continued
description, 2-9
sample application, 2-9
typical application, 3-12
oversize display, 5-12
P
PAK, 6-9, 7-29, G-12
PAK command, 7-29
Parity command, 7-38
PC-IRL, 9-9
pin assignments
25 pin modem connector, 2-11
25 pin terminal connector, 2-12
25-pin modem connector, A-6
25-pin terminal connector, A-6
6-pin wand connector, A-5
9-pin laser scanner connector, A-5
Point-to-Point protocol, 5-6, G-13
POL, 5-5, 5-6, 5-7, 6-8, G-13
POL command, 7-39
Poll character (POL), 7-4
Poll command, 7-39
Poll event, 5-5
Polling Mode D protocol, 5-6, 5-7, 6-6, G-14
port concentrator, 2-14, 2-15
postamble, 5-10, 8-4, G-13
Postamble C command, 8-27
power cable, 2-18, 3-4
power supply, 2-3, 2-18, 3-5
preamble, 5-10, 5-17, G-14
Preamble A command, 8-25
Preamble A Required command, 7-40
Preamble B command, 8-26
program
compiling, 9-7
creating, 9-6
running, 9-7
Program Acknowledgement command, 7-29
Program disk, MAGDRVR.IRL, 9-14
Program Statement Separator (IRL), G-14
Program Statement Separator command, 7-30
Prompting Configuration mode, 1-6, 6-3, 6-12
moving around, 6-13
Prompts, 6-16, 6-21
Prompting Configuration Mode command, 8-14
protocol
asynchronous, 5-5, 5-6, 5-7
configuration, 6-6, 6-7, 6-8, 6-9
defining a secure, 5-8
error checking, 5-7
full-duplex, 5-5, 5-6
half-duplex, 5-5, 5-7
Multi-Drop, 5-6, 5-7, G-12
nonpolling, 5-6
Point-to-Point, 5-6, G-13
Polling Mode D, 5-6, 5-7, G-14
solicited, 5-7
User-Defined, 5-8, G-18
protocol acronyms
AFF, G-3
LRC, G-11
NEG, G-12
POL, G-13
REQ, G-14
RES, G-15
RX EOM1, G-15
RX EOM2, G-15
TX EOM1, G-17
TX EOM2, G-17
XOFF, G-18
XON, G-18
Protocol command, 7-41
protocol control characters, 5-8
PSS, 6-9
PSS command, 7-30
Q
queue, 5-9
quiet zone, 4-9, G-14
R
RAM, 1-6
reader prompts, 5-12
reader warning messages, 5-13
reading bar code labels, 4-5
Receive End of Message First character, G-15
Receive End of Message Second character, G-15
received data, buffering, 5-9
record, 5-11
records per block, 5-11, 6-8
Records per Block command, 7-42
register #0, 2-8
regular bar code label, 4-5
regular label, 4-5, G-14
remote triggering, 2-6, 2-7
enable with hardware, 2-6, 2-7
REQ, 5-9, 6-8, G-14
REQ command, 7-43
Request for Acknowledgment (REQ), G-14
Request for Acknowledgment command, 7-43
RES, 5-9, 6-8, 10-7, G-15
RES command, 7-44, 8-28
Reset character, G-15
Reset command, 7-44, 8-28
Restore Configured Character Set command, 5-14
Restore Cursor Position command, 5-14
Resume IRL command, 7-45, 9-7, 9-8
Resume Program command, 8-28