Intellijel Steppy 3U Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 37

Intellijel Steppy 3U Скачать руководство пользователя страница 5

/

Steppy 3U Manual

Most   modules   will   come   with   the   cable   already   connected   but   it   is   good   to   double   check   the
orientation.   Be   aware   that   some   modules   may   have   headers   that   serve   other   purposes   so
ensure   the   cable   is   connected   to   the   right   one.

The   other   end   of   the   cable,   with   a   16-pin
connector,   connects   to   the   power   bus   board   of
your   Eurorack   case.   Ensure   the   red   stripe   on
the   cable   lines   up   with   the   -12V   pins   on   the   bus
board.   On   Intellijel   power   supplies   the   pins   are
labelled   with   the   label   “-12V”   and   a   thick   white
stripe:

If   you   are   using   another   manufacturer’s   power
supply,   check   their   documentation   for
instructions.

Once connected, the cabling between the module and power supply should resemble the
picture below:

Before   reconnecting   power   and
turning   on   your   modular   system,
double   check   that   the   ribbon   cable
is   fully   seated   on   both   ends   and
that   all   the   pins   are   correctly
aligned.   If   the   pins   are   misaligned
in   any   direction   or   the   ribbon   is
backwards   you   can   cause   damage
to   your   module,   power   supply,   or
other   modules.

After   you   have   confirmed   all   the
connections,   you   can   reconnect
the   power   cable   and   turn   on   your

modular   system.   You   should   immediately   check   that   all   your   modules   have   powered   on   and   are
functioning   correctly.   If   you   notice   any   anomalies,   turn   your   system   off   right   away   and   check
your   cabling   again   for   mistakes.

Page 4

«
...
3
4
5
6
7
...
»

Содержание Steppy 3U






































Отзывы:

Нет отзывов