Intellijel Steppy 3U Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 37

Intellijel Steppy 3U Скачать руководство пользователя страница 25

/

Steppy 3U Manual

6. Probability (PROB) button

When   in   Edit   mode,   press   this   button   to   set   the
probability   that   any   step   within   the   pattern   will   actually
play   when   requested.   Probability   editing   is   available
when   the   PROB   button   glows

red

.

When   editing   probability   values,   the   left   column   of
buttons   set   the   probability   percentage.   Pressing
buttons   toward   the   top   results   in   low   probability;
pressing   buttons   toward   the   bottom   results   in   a   higher
probability   that   any   programmed   step   will   play.   The
bottom   button   (100%)   is   the   default.   This   means   your
pattern   will   play   exactly   as   programmed   every   single
time.

To   set   a   Probability   for   the   selected   track,   simply
press   the   left   column   button   corresponding   to   the
desired   value.   If   you   press

and hold

the value button,

you apply the Probability setting to all four tracks
simultaneously.

In   this   example,   probability   is   set   to   75%.   That   means
each   step   in   the   track   has   a   75%   chance   of   playing.
Which   means,   on   average,   each   step   will   play   3   out   of
the   4   times   you   programmed   it   to   play.

Page 24

«
...
23
24
25
26
27
...
»

Содержание Steppy 3U






































Отзывы:

Нет отзывов