Intellijel Steppy 3U Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 37

Intellijel Steppy 3U Скачать руководство пользователя страница 19

/

Steppy 3U Manual

All edited track parameters (Swing, Delay, Probability, etc) are respected when looping,
and looping applies to all tracks when engaged.

To

latch Loopy playback

:

1. While holding down the two buttons that define the length of the Loopy

sequence, short-press the

SELECT

button.

You can now release your hold on the two buttons, since pressing the

SELECT

button during Loopy playback latches it.

2. Press any of the step buttons to unlatch the Loopy function, and return to normal

playback.

7. RESET button

When   in   Select   mode,   press   this   button   to   reset   all   patterns   (across   all   four   tracks)   back
to   their   first   step.   This   is   particularly   useful   if   your   tracks   have   different   lengths   and   you
wish   to   re-align   them   to   the   first   beat.   This   button   replicates   the   functionality   of   the   RST
input   jack.   Pressing   the   RESET   button   causes   all   16   buttons   to   briefly   flash

green

—

indicating the reset operation has occurred.

If Steppy is in RUN Mode (see the

RESET (RST) IN

jack description in

), then the button is lit

yellow

to indicate that Steppy is in RUN mode.

PANIC   feature:   In   Select   mode,   if   you   long   press   the   RESET   button   (i.e   hold   the   RESET
button   for   >1   second),   you’ll   send   a   gate   off   to   all   the   outputs.   This   is   useful   in   the
unlikely   event   that   one   of   the   outputs   gets   stuck   “on”   when   Steppy’s   input   clock   is
stopped   or   removed.

8. CLEAR button

When in Select mode, the button performs two different functions depending on how
long it’s held down. Specifically;

●

Short-press

(button pressed and quickly released): Short-press the CLEAR

button   to   clear   all   steps   from   the   active   track   (turning   all   gates   to   off).   This   causes
all   16   buttons   to   briefly   flash   red   —   indicating   that   the   gates   have   been   cleared.
Short-pressing   the   CLEAR   button   only   clears   the   trigger   pattern   from   a   Track.
Any   track   parameters   (such   as   Gate   Length,   Clock   Division,   or   Probability)
remain   part   of   the   track   and   will   affect   any   new   pattern   you   create.

●

Long-press

(button pressed and held for 1-second): Press and hold the CLEAR

button for 1 second to clear the entire contents of a Track, meaning its gate
pattern

plus

all its Track parameters (such as Gate Length, Clock Division, and

Probability).

Page 18

«
...
17
18
19
20
21
...
»

Содержание Steppy 3U






































Отзывы:

Нет отзывов