manualshive.com logo in svg

Intellihot iN401, Руководство по эксплуатации и установке

Поделиться
Скачать
Intellihot iN401 Скачать руководство пользователя страница 74

iN401 - iN501 Warranty

70

May

 

2019

 

-

 

Revision

 00 

Not Covered by this Warranty

This warranty does not cover failures or problems due to:

• Failure to install in accordance applicable building codes,

ordinances, normal plumbing, or electrical trade practices.

• Improper installation, improper use, improper maintenance,

improperly made replacements or repairs, accidents or

abuse.

• Sediment deposits, fire, flood, lightning, freezing, and acts

of God, or any causes other than defects in materials and

workmanship.

This warranty will be void and have no effect if:

• The unit is modified or altered in any way.

• Appliance(s) or equipment attached to the unit that have

not been approved by Intellihot Inc.

• If the unit is used exclusively as a booster heater for a

commercial dishwasher, or if the water from a reverse

osmosis or deionized process is run directly through the

unit.

• The serial number is altered, defaced, or discarded.

Warranty Limitations

This warranty applies only when the unit is used in the United 
States or Canada. Except for the limited warranties provided 
above, Intellihot Inc. disclaims any and all other warranties, 
including but not limited to warranties of merchantability 
and fitness for a particular purpose; provided however, 
that implied warranties of merchantability and fitness for 
a particular purpose are not disclaimed during the 1-year 
period from 

the date of commissioning

. Intellihot shall not be 

liable for indirect, special, incidental, consequential, or other 
similar damages, including lost profits, arising from or relating 
to the unit. This warranty gives you specific legal rights, and 
you may also have other rights which vary from state to 
state.

How to Make a Claim

Please Call (877) 835-1705. Proof of purchase in the form of a 
dated sales receipt or warranty registration should be included 
with your claim. The product owner should submit the 
warranty claim directly to Intellihot at the following address:

Intellihot Inc.
Attn: Warranty Claims
2900 W. Main St.
Galesburg, IL 61401

All parts claimed to be defective may be requested to be 
returned to Intellihot for examination prior to full claim 
settlement.  Please include the following information on your 
warranty claim:

• Model number and serial number of the unit.

• Date of original purchase.

• Owner’s name and address.

• A description of the problem with the part and unit.

Содержание iN401

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды