Intellihot iN401 Скачать руководство пользователя страница 18

Страница: 18 / 80

iN401 - iN501 Gas

Connection

May

2019

Revision

6. Gas Connection

WARNING

FIRE AND/OR EXPLOSION HAZARD

To avoid serious injury or even death, the gas line

installation and the gas line inlet pressure test must be

done by a licensed professional.

Always match the water heater with the type of gas

supplied to the unit (natural gas or propane). The water

heater is factory preset for natural gas.

Make sure the gas line pressures are within normal

limits. Pressures outside normal limits can result in

poor performance and hazardous operating conditions.

6.1 Quick Reference Installation Instructions

1. Determine fuel source; natural gas or propane as shown in

“6.2 Fuel Source” on page 14.

2. Measure gas pressure as shown in “6.3 Gas Pressure

Requirements” on page 14.

3. Install a gas pressure regulator and vent line if gas

pressure is above maximum recommendations as shown

in “6.4 Gas Pressure Regulator” on page 14.

4. Measure the length of the supply line as shown in “6.5

Length of Gas Supply Line” on page 15”.

5. Select the proper gas piping material as shown in “6.6

Gas Piping Material” on page 15.

6. Select the proper gas piping diameter as shown in “6.7

Determine Correct Gas Pipe Diameter” on page 15.

7. Install a drip leg on the gas piping as shown in “6.8 Gas

Pipe Drip Leg and Shut-off Valve” on page 15.

8. Install a manual shut-off valve as shown in “6.8 Gas Pipe

Drip Leg and Shut-off Valve” on page 15.

9. Test all gas line connections for leaks.

NOTICE

Do not fire (operate) the water heater until all connections

have been completed and the heat engine is filled with

water.

6.2 Fuel Source

1. Natural gas is the factory preset.

2. To convert the unit to propane, refer to the Propane

(LPG) Conversion section in this manual.

6.3 Gas Pressure Requirements

iN series water heaters are designed to operate at gas

pressures as low as 2.5” WC (at maximum firing rate). Gas

inlet pressures to each unit should not exceed 14” WC under

any condition (when unit is firing or not firing).

Natural Gas Static Gas Pressure

Parameters

Specifications

Minimum Static Gas Pressure

2.5”

W.C.

(non-corrugated,

black

iron)

Recommended

Gas

Pressure

8”

W.C.

Maximum Static Gas Pressure

14”

W.C.

6.4 Gas Pressure Regulator

If the gas inlet pressure is higher than recommended,

install a gas pressure regulator to lower gas pressure to

an acceptable level.

The gas pressure regulator must have the same or higher

minimum to maximum modulation range as the model

it is

regulating. For example, an iN401 gas pressure

regulator

should have a modulation range of 30,000

BTU/h to

399,999 BTU/h.

Regulators should be mounted with a minimum of 12” of

straight length pipe on either side and a recommended 6

ft from the appliance. If regulator manufacturer

recommends more distance, then follow their guidelines.

Содержание iN401

















































































Результаты поиска

Содержание iN401

Отзывы:

Бренды по названию

Популярные бренды

Intellihot iN401, Руководство по эксплуатации и установке

Результаты поиска

Содержание iN401

Отзывы:

Бренды по названию

Популярные бренды