Intellihot iN401 Скачать руководство пользователя страница 7

Страница: 7 / 80

iN401 - iN501 Safety

May

2019

Revision

2. Safety

2.1 Safety Signal Words

DANGER

Indicates an imminently hazardous situation which, if

not avoided, will result in death or serious injury. This

signal word is limited to the most extreme situations.

WARNING

Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury.

NOTICE

Indicates that equipment or property damage can result if

instructions are not followed.

SAFETY

INSTRUCTIONS

Safety instructions (or equivalent) signs indicate

specific safety-related instructions or procedures.

Note:

Contains additional information important to a

procedure.

2.2 Installation Warnings

WARNING

DO NOT use this water heater for any purpose other

than water heating.

Read, understand, and follow the Installation and Operation

manuals, including all warnings and precautions, before

operating this water heater. If you do not follow these

instructions exactly, a fire or explosion may result, causing

property damage, personal injury, or loss of life.

Follow all local codes and the most recent edition of the

National Fuel Gas Code (ANSI Z223.1/NFPA 54) in the USA

or the Natural Gas and Propane Installation Code in Canada

(CSA B149.1).

This water heater must be installed by a licensed plumber,

gas fitter, and/or professional service technician. Installation

by unqualified person(s) voids the warranty.

Designed for operations at outlet temperature(s) not in

excess of 190°F (88°C).

DANGER

A. This water heater does not have a pilot. It is equipped

with an ignition device which automatically lights the

burner. Do not try to light the burner manually.

BEFORE OPERATING, smell all around the water

heater area for gas. Be sure to smell next to the floor

because some gas is heavier than air and will settle

on the floor.

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electric switch; do not use any phone in

your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire or

police department.

C. Use only your hand to turn the manual gas shut-off

valve. Never use tools. If manual gas shut-off valve will

not turn by hand, don’t try to repair it. Call a qualified

service technician. Force or attempted repair may

result in a fire or explosion.

WARNING

DO NOT use or store flammable liquids around the water

heater, including gasoline, oils, spray paints, etc.
DO NOT operate this water heater unless it is properly

vented to the outside (the exhaust vent piping must be

connected from the unit directly to the outside). Improper

venting can cause a build-up of carbon monoxide, which

can result in brain damage or death. Exhaust gases must

be completely expelled out of the building.
This water heater is factory preset for NATURAL GAS

but may be field converted for use with propane.

For propane conversion, refer to the Propane (LPG)

Conversion section of this manual. Connecting the

water heater to any other gas supply can result in

property damage, serious injury, or even death.
This water heater is suitable for use in potable water

heating applications. The cold and hot water fittings on

the top of the water heater MUST NOT be connected to

any heating system.
The water heater temperature is factory set to 120°F

(49°C). Hot water temperatures above 125°F can cause

severe burns instantly or death from scalds. If the

proposed water heater outlet temperature is to be set

above 125°F, installation of a thermostatically controlled

(or temperature limiting) mixing valve is recommended

for all hot water going to faucets to avoid the risk

of scalding. Examples include commercial applications

where 140°F (60°C) is often needed or if the space

heating temperature required is higher than the domestic

hot water. Always check the temperature of the hot

water before bathing, showering, washing, etc.
Protect against snow and debris accumulation around

the vent terminations. Regularly inspect the exhaust

vent pipe and the air intake pipe to ensure they remain

clear from obstructions at all times.

Содержание iN401

















































































Результаты поиска

Содержание iN401

Отзывы:

Бренды по названию

Популярные бренды

Intellihot iN401, Руководство по эксплуатации и установке

Результаты поиска

Содержание iN401

Отзывы:

Бренды по названию

Популярные бренды