manualshive.com logo in svg

Intellihot iN401, Руководство по эксплуатации и установке

Поделиться
Скачать
Intellihot iN401 Скачать руководство пользователя страница 39

35 

iN401 - iN501 Natural

 

Gas

 

to

 

Propane

 

Conversion 

May

 

2019

 

-

 

Revision

 

00

11. Natural Gas to Propane Conversion

SAFETY

INSTRUCTIONS

A qualified service technician MUST make the required 

changes to convert the water heater from Natural Gas 

to Propane.

11.1  General Information

Note: 

This

 

conversion

 

process

 

also

 

requires

 

the

 

CO

2

 

levels to be adjusted.  Refer to “11. Natural Gas to Propane 

Conversion” on page 35 for instructions.

Before converting the unit for propane, verify the current 

gas inlet pressure meets the recommended pressure and 

record it in the space below.

Propane Static Gas Pressure

Parameters

Specifications

Minimum Static Gas Pressure

8”

 

W.C.

 

(non-corrugated,

 

black

 

iron)

Recommended

 

Gas

 

Pressure

11”

 

W.C.

Maximum Static Gas Pressure 

13”

 

W.C.

Current

 

Static

 

Propane

 

Gas

 

Pressure

 

___________W.C.

Date

 

___________________

Note: 

This

 

conversion

 

process

 

also

 

requires

 

the

 

CO

2

 levels 

to be adjusted.  Refer to “10. Adjusting CO2 Level” on page 

32 for instructions.

11.2  Conversion Procedure 

1. Follow these steps before repositioning the DIP switches.

a. Turn the water heater OFF using the display screen.

b. Place the circuit breaker for the water heater at the

main electrical panel in the OFF position.  Verify there

is no power to the unit(s).

c. Open the front door and locate the main circuit board.

Note:

  There are two control boards in the iN401/iN501.

d. Locate DIP Switch 1 on each of the two circuit boards.

e. Move each DIP switch downward into the Propane

position.

SW1

Propane

DIP Switch Settings 

(Réglages des commutateurs DIP)

Natural Gas 

(Gaz  naturel)

ON

ON

Содержание iN401

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды