Intellihot iN401 Скачать руководство пользователя страница 35

Страница: 35 / 80

iN401 - iN501 Electrical Power

May

2019

Revision

9. Electrical Power

9.1 Electrical Recommendations

WARNING

To avoid serious injury or even death, follow all applicable

local, state, and national regulations, mandates, and

building codes for guidelines to install the electrical

power supply.

Electrical code requirements are different in the USA and

Canada. Refer to and follow the local building codes, the

latest edition of the National Electrical Code (NFPA 70) in

the USA, or the CGA C22.1 Canadian Electrical Code - Part 1.

For a single in401 or iN501 water heater, the circuit

breaker(s) should be at least 15 amps per circuit

For multiple units install an adequately sized circuit

breaker. Installing a separate circuit breaker for each unit is

recommended to isolate units during service or repair.

20 (30) Amp

Single Unit

80 (120) Amp

Four Units

Note:

For an electrical wiring schematic, refer to “15.2

Complete Wiring Diagram (all models)” on page 53 for

additional information.

NOTICE

The electrical connections for the water heaters are

polarity sensitive. Before connecting the water heater to

the power source, test the polarity of the electrical circuit.

9.2 Connection Instructions

1. On single unit installations, make sure the electrical

outlet being used is wired with at least 12 gauge wire and

grounded with an appropriately sized circuit breaker. The

electrical power required for the water heater is 120V AC

at 60 Hz.

2. Remove the two cover screws and open the cover.

WARNING

To avoid serious injury or even death from electrical

hazards, an additional ON/OFF electrical junction box

should be installed near the water heater. This switch

will allow power to be removed from the water heater

prior to service or in the case of an emergency.

3. Route a customer-supplied appropriately-sized, wire with

ground from an electrical junction box with an ON/OFF

switch through the back panel of the water heater. Route

the wire through the cabinet to the junction box.

4. On the opposite side of the block from the factory

installed wiring, connect the white wire to the white

terminal, the black wire to the black terminal, and the

green ground wire to the green terminal (for each circuit).

5. If multiple units are being installed, refer to “13.

Connecting Multiple Units” on page 48 for additional

information.

Содержание iN401

















































































Результаты поиска

Содержание iN401

Отзывы:

Бренды по названию

Популярные бренды

Intellihot iN401, Руководство по эксплуатации и установке

Результаты поиска

Содержание iN401

Отзывы:

Бренды по названию

Популярные бренды