Intel BX80605X3440 - Quad Core Xeon X3440 страница 33 Скачать руководство пользователя

Страница: 33 / 106

Thermal/Mechanical Specifications and Design Guidelines

LGA1156 Socket and ILM Electrical, Mechanical, and Environmental Specifications

LGA1156 Socket and ILM

Electrical, Mechanical, and

Environmental Specifications

This chapter describes the electrical, mechanical, and environmental specifications for
the LGA1156 socket and the Independent Loading Mechanism.

5.1

Component Mass

5.2

Package/Socket Stackup Height

Table 5-2

provides the stackup height of a processor in the 1156-land LGA package and

LGA1156 socket with the ILM closed and the processor fully seated in the socket.

Notes:

This data is provided for information only, and should be derived from: (a) the height of the socket seating

plane above the motherboard after reflow, given in

Appendix C

, (b) the height of the package, from the

package seating plane to the top of the IHS, and accounting for its nominal variation and tolerances that

are given in the corresponding processor datasheet.

The integrated stackup height value is a RSS calculation based on current and planned processors that will

use the ILM design.

5.3

Socket Maximum Temperature

The power dissipated within the socket is a function of the current at the pin level and
the effective pin resistance. The key temperature limit for the LGA1156 socket is:

• Socket contact interface with package < 100 °C.

Table 5-1.

Socket Component Mass

Component

Mass

Socket Body, Contacts and PnP Cover

10 g

ILM Cover

29 g

ILM Back Plate

38 g

Table 5-2.

1156-land Package and LGA1156 Socket Stackup Height

Component

Stackup Height

Note

Integrated Stackup Height

(mm)

From Top of Board to Top of IHS

7.781 ± 0.335 mm

Socket Nominal Seating Plane Height

3.4 ± 0.2 mm

Package Nominal Thickness (lands to top of IHS)

4.381 ± 0.269 mm

Содержание BX80605X3440 - Quad Core Xeon X3440











































































































Результаты поиска

Содержание BX80605X3440 - Quad Core Xeon X3440

Отзывы:

Похожие инструкции для BX80605X3440 - Quad Core Xeon X3440

Бренды по названию

Популярные бренды

Intel BX80605X3440 - Quad Core Xeon X3440, Справочник

Результаты поиска

Содержание BX80605X3440 - Quad Core Xeon X3440

Отзывы:

Похожие инструкции для BX80605X3440 - Quad Core Xeon X3440

Бренды по названию

Популярные бренды