Integra DTR-50.5, Инструкция по эксплуатации

Страница: 56 / 108

Advanced Operations
En-56
Operating
procedure
(
➔
page 54 )
Speaker Levels
■
Subwoofer Level
`
–15.0dB to 0.0dB to +12.0dB in 0.5 dB steps.
■
Center Level
`
–12.0dB to 0.0dB to +12.0dB in 0.5 dB steps.
You can adjust the volume of each speaker while
listening to an input source.
These temporary adjustments are cancelled when the
AV receiver is set to standby. To save the setting you
made here, go to “Level Calibration” (
➔
page 63 )
before setting the AV receiver to standby.
Note
• You cannot use these function while the AV receiver is
muted.
• These settings cannot be used while a pair of headphones
is connected.
• Speakers that are set to “ No ” or “ None ” in
“Speaker Configuration” (
➔
page 62 ) cannot be adjusted.
Audyssey ®
■
Audyssey
See “Audyssey” in “4. Source Setup” (
➔
page 67 ).
■
Dynamic EQ
See “Dynamic EQ” in “4. Source Setup” (
➔
page 67 ).
■
Dynamic Volume
See “Dynamic Volume” in “4. Source Setup”
(
➔
page 67 ).
Note
• These technologies can be used when all the following
conditions are met:
– Room Correction and Speaker Setup is completed. Note
that “ Audyssey ” requires the “ Audyssey MultEQ Full
Calibration ” method.
– Any listening mode other than Direct is selected.
– A pair of headphones is not connected.
• The setting is stored individually for each input selector.
• “ Dynamic EQ ” and “ Dynamic Volume ” cannot be selected
when any of the THX listening modes is selected, with
“
Loudness Plus ” set to “ On ” or “ Preserve THX Settings ”
set to “ Yes ” (
➔
page 64 ).
Late Night
■
Late Night
For Dolby Digital and Dolby Digital Plus sources,
the options are:
`
Off
`
Low :
Small reduction in dynamic range.
`
High :
Large reduction in dynamic range.
For Dolby TrueHD sources, the options are:
`
Auto :
The Late Night function is set to “ On ” or “ Off ”
automatically.
`
Off
`
On
Turn this setting on to reduce the dynamic range of
Dolby Digital material so that you can still hear quiet
parts even when listening at low volume levels—ideal
for watching movies late at night when you don’t want
to disturb anyone.
Note
• The effect of the Late Night function depends on the
material that you are playing and the intention of the original
sound designer, and with some material there will be little
or no effect when you select the different options.
• The Late Night function can be used only when the input
source is Dolby Digital, Dolby Digital Plus, or Dolby
TrueHD.
• The Late Night function is set to “ Off ” when the AV receiver
is set to standby. For Dolby TrueHD sources, it will be set
to “
Auto ”.
• With Dolby TrueHD sources, the Late Night function cannot
be used when “ TrueHD Loudness Management ” is set to
“ Off ”.
Music Optimizer
■
Music Optimizer
`
Off
`
On
The Music Optimizer function enhances the sound
quality of compressed music files. When set to “
On ”,
the M.Opt indicator lights on the AV receiver’s
display.
Note
• The Music Optimizer function only works with PCM digital
audio input signals with a sampling rate below 48 kHz and
analog audio input signals.
When
NET or USB input selector is selected, this function
even works with digital audio input signals with a sampling
rate below 48 kHz (except DSD signals and Dolby TrueHD
signals) regardless of the PCM digital audio input signals
with a sampling rate below 48 kHz.
• The Music Optimizer is disabled when the Direct listening
mode is selected.
• The setting is stored individually for each input selector.