14.02-5
2100-A
16
Output Specifications.
Dual Analogue Outputs:
Analogue Outputs supplied from factory as mA. V must be factory fitted.
-Resolution
2 Outputs, 12bits, 4000 Steps Typical. (Some ranges may differ.)
-V Ranges
0~10V, 2~10V. Output Drive = 4mA Maximum. (2k5 @ 10V)
-mA Ranges
0~20mA, 4~20mA. Output Drive = 12V Maximum. (600 @ 20mA)
Digital Outputs:
2 Isolated Relays with LED Indication of Each Output.
-Functions
2 on Board Controllers (16 with 2100-R2), Can be used as Set Point (SV)
Switching Differential, Auto/Manual, Manual Output Setting, Dual Action Control,
Single Action Control, Heat/Cool, Cool Only, Heat Only.
-Contact Material
Gold Clad Silver.
-Relay Ratings
30Vac/dc, 1A Maximum.
-Approved to Standard
UL & CSA:.
-Number of Operations
1 x 10
5
Min, at 30Vac/dc, 1A, Resistive Load.
2100-A
16
General Specifications.
Comms:
-Protocols
Intech Scada; PLC Message; Modbus RTU; RS422/RS485 or RS232
-Baud Rate
Selectable 2400, 4800, 9600. (Default = 9600).
-Format
8 bit, No Parity, 1 Stop. (Not selectable.)
-Modbus RTU
Refer to Modbus section, Page 20, for more details.
-Ethernet 10/100
Refer to Ethernet 10/100 section, Page 23, for more details.
Power:
-H
85~264Vac/dc; 50/60Hz; 10VA.
-M
23~90Vdc; 10VA.
-L
10~28Vac/dc; 50/60Hz; 10VA.
Refer to ‘
2100-A
16
H1 Power Supply Settings’
for voltage selection instructions.
Transmitter Power Supply
20Vdc±5%; Max. Load=50mA; Ripple<20mVrms; Common to Analog Inputs.
Transmitter power supply is not available with Ethernet 10/100 comms option.
Safety and EMC Compliances:
EMC Compliances
Emissions EN 55022-A. Immunity EN 50082-1.
Safety Compliance
EN 60950.
Mains Isolation
250Vac.
Mains Isolation Test Voltage
-To all Inputs and Outputs:
3000Vac 50Hz for 1min.
-To Earth
1500Vac 50Hz for 1min.
Input/Output Isolation Test Voltages
-Digital Input to Analogue Input/Output:
1000Vdc for 1min.
-Digital Input to Digital Output:
1000Vdc for 1min.
-Analogue Input/Output to Digital Output:
100Vdc for 1min.
-Comms to Analogue Input/Output:
1000Vdc for 1min.
-Comms to Digital Input/Output:
1000Vdc for 1min.
General Specifications:
(Unless otherwise stated in other input specifications.)
Accurate to
<±0.1% FSO Typical.
Linearity & Repeatability
<±0.1% FSO Typical.
Channel Separation
<±0.1% FSO Typical.
Ambient Drift
<±0.01%/C FSO Typical.
Noise Immunity
125dB CMRR Average Differential Input 18Vpeak.
RF Immunity
<±1% Effect FSO Typical.
A01 & AO2
25msec. Nominal Pulse Length.
-(used as CLOCK and RESET)
20mA Nominal Current.
Settling Time and Averaging Software Selectable.
Permanent Memory (E
2
ROM)
10,000 Writes per Input Parameter.
-(2100-ME fitted)
10 Year Data Retention.
Operating Temperature
0~60C.
Storage Temperature
-20~80C.
Operating Humidity
5~85%RH Max. Non-Condensing.
Housing
-Material
ABS Inflammability V0 (UL94)
-Dimensions
L=195, W=120, H=70mm.
-Mounting
35mm Symmetrical Mounting Rail.
-Weight
800g. Includes Packaging.
Note 1. Contact INTECH INSTRUMENTS for more detailed programming information.
Note 2. For mA inputs a 2 pin jumper must be installed for each input.
Note 3. The 2100-A16 is C and F selectable. This selection affects all temperature readings. (CJC must be calibrated in C.)
Product Liability.
This information describes our products. It does not constitute guaranteed properties and is not intended to affirm the suitability
of a product for a particular application. Due to ongoing research and development, designs, specifications, and documentation are subject to
change without notification. Regrettably, omissions and exceptions cannot be completely ruled out. No liability will be accepted for errors, omissions
or amendments to this specification. Technical data are always specified by their average values and are based on Standard Calibration Units at
25C, unless otherwise specified. Each product is subject to the ‘Conditions of Sale’.
Warning: These products are not designed for use in, and should not be used for patient connected applications. In any critical installation
an independant fail-safe back-up system must always be implemented.
CAUTION: Dangerous Voltages may be present. The 2100-A
16
has no user serviceable parts.
Protective enclosure only to be opened by qualified personnel.
Remove ALL power sources before removing protective cover.
