background image

                                                             

Digital multimeter                             

 

1

 / 

25

 

Ⅰ. Overview 

 

     

As a kind of intelligent 3 5/6 digital multimeter with automatic identification, steady performance and high 

reliability,  this  meter  is  equipped  with  LCD  display  device  with  the  text  height  of  33mm  which  features 

clear reading, direct-viewing display and convenient  operation. It can be used to measure DC voltage, AC 

voltage, DC current, AC current, resistance, capacitance, frequency, diode and continuity test; meanwhile, it 

is  available  for  unit  symbol  display,  data  retention,  the  measurement  of  maximum  and  minimum  value, 

automatic/manual range switching, automatic power off and alarm function. The complete machine takes a 

switching integrated circuit which can directly drive LCD microprocessor and double-integrating A/D and a 

digital  display  drive  offering  high  resolution  and  high  precision.  Since  the  meter  features  complete 

functions,  high  measurement  accuracy  and  convenient  operation,  it  is  the  ideal  tool  in  laboratory  and 

factory as well as for radio fans and family. 

 

 

Ⅱ. Open-package Inspection 

 

Open  the  package  box  and  take  out  the  meter,  check  carefully  if  the  following  accessories  are  absent  or 

damaged. If there is any absence or damage, please contact the distributor immediately. 

Summary of Contents for VC70D


























Reviews: