Intech Micro 2100-A16, Руководство по установке

Страница: 12 / 28

Connecting the 2100-A16 to the 2100-ME.
1/ Only fit 2100-ME-32 to 2100-A16 Rev.1.3.
2/ Power must be off before installing the 2100-ME.
3/ Remove the cover off the 2100-A16.
4/ Use antistatic precautions when installing the 2100-ME.
Carefully orientate the 2100-ME board as shown above.
Locate the two plastic stand-offs over the corresponding holes
in the 2100-A
16
, and the 10 pin connector. Once all three are
aligned, push the 2100-ME firmly into the 2100-A
16
.
5/ Install a link in position 4 of the 2100-A
16
S1 Function jumper.
6/ Replace the 2100-A
16
cover.
7/ When the 2100-A
16
is used with the 2100-ME, the 2100-M
and 2100-R expansion options are unavailable.
8/ The 2100-ME can only be fitted to a 2100-A
16 REV 1.3.
2100-A
16
Memory Expansion - Using 2100-ME Memory Expansion Card.
The 2100-ME Memory Expansion Card is designed to allow the 2100A
16
to stand alone, retaining the data collected for
intermittent download. Data is held in permanent memory.
.
2100-ME
CAUTION: Dangerous Voltages may be present. The 2100-A
16
has no user serviceable parts.
Protective enclosure only to be opened by qualified personnel.
Remove ALL power sources before removing protective cover.
14.02-12
2100-A
16
Connection Example Diagram for Using the 2100-RL2, 2 Relay Slave Board.
2100-A
16
Relay 2 52
Relay 1 51
COM 50
20Vdc 49
0V 48
2100-RL2
52
51
50
49
48
NC
Relay 1 COM
NO
NC
Relay 2 COM
NO
2100-RL2 Relay Specifications:
-Contact Material
Silver Alloy
-Relay Ratings Rating Approved
250Vac, 2A UL
125Vac, 2A CSA
110Vdc, 0.3A;
30Vdc, 2A;
250Vac,1/6hp;
125Vac, 1/10hp.
-Number of Operations 2 x 10
5
Min, at 1A, 250Vac
Note 1. Activating Relay 1 on the 2100-A
16
activates
Relay 1 on the 2100-RL2. Activating Relay 2 on
the 2100A
16
activates Relay 2 on the 2100-RL2.
2100-A
16
Analogue Outputs Controlled by Scada.
The analogue output mode is set in the Station Advanced Dialog Box ‘AO 1 & AO 2 button’.
For Scada outputs select Mode 2.
For detailed programming info, refer to ‘Programming 2100-Series Remote Station’ in the Microscan Manual.
AO 1 & AO 2 are controlled by the Scada Software.
12 bit output nominally = 0~4095 for 4~20mA (or 0~10V etc.) out:
0bit = 4mA (0V);
2048 = 12mA (5V);
4095 = 20mA (10V).
For 4~20mA output, Loop Powered Indicators can
be used. 12V maximum at 20mA (600 at 20mA)
2100-A
16
62
61
60
AO 2
AO 1
AO COM
INDICATOR
INDICATOR