Customer Services (858) 578-7887 & (888) GO IN
TEC
IN
TEC
Controls, 12700 Stowe Dr., Suite 1
0
0, Poway, CA 92064
Fax (858) 578-4633 & (888) FX IN
TEC
www.inteccontrols.com
Specification subject to change without notice.
Printed in USA 140403
Polygard® is a registered trademark of MSR
GAADT531193_E_1011.pdf
PolyGard
®
CL
2
Gas Transmitter
User Manual - AT-1193
Page 13
11 Part Disposal
Since August 2005 there are EC-wide directives defined in the EC Directive 2002/96/EC and in national
codes concerning the waste electrical and electronic equipment and also regarding this device.
For private households there are special collecting and recycling possibilities. For this device isn’t registered
for the use in private households, it mustn’t be disposed this way. You can send it back to your national
sales organization for disposal. If there are any questions concerning disposal please contact your
national sales organization.
Outside the EC, you have to consider the corresponding directives.
12 Notes and General Information
It is important to read this user manual thoroughly and clearly in order to understand the information
and instructions. The PolyGard
®
transmitters must be used within product specification capabilities. The
appropriate operating and maintenance instructions and recommendations must be followed.
Due to on-going product development, MSR and IN
TEC
Controls reserve the right to change
specifications without notice. The information contained herein is based upon data considered to be
accurate. However, no guarantee is expressed or implied regarding the accuracy of this data.
12.1 Intended Product Application
The PolyGard
®
Cl
2
transmitters are designed and manufactured for control applications and air quality
compliance in commercial buildings and manufacturing plants.
12.2 Installers’ Responsibilities
It is the installer’s responsibility to ensure that all PolyGard
®
transmitters are installed in compliance with
all national and local codes and OSHA requirements. Installation should be implemented only by
technicians familiar with proper installation techniques and with codes, standards and proper safety
procedures for control installations and the latest edition of the National Electrical Code (ANSI/NFPA70). It
is also essential to follow strictly all instructions as provided in the user manual.
12.3 Maintenance
It is recommended to check the PolyGard
®
transmitter regularly. Due to regular maintenance any
performance deviations may easily be corrected. Re-calibration and part replacement in the field may be
implemented by a qualified technician and with the appropriate tools. Alternatively, the easily removable
plug-in transmitter card with the sensor may be returned for service to IN
TEC
Controls.
12.4 Limited Warranty
MSR-Electronic-GmbH and IN
TEC
Controls warrants the PolyGard
®
transmitters for a period of (2) years
from the date of shipment against defects in material or workmanship and 12 months normal exposure for
sensor element. Should any evidence of defects in material or workmanship occur during the warranty
period, IN
TEC
Controls will repair or replace the product at their own discretion, without charge.
This warranty does not apply to units that have been altered, had attempted repair, or been subject to
abuse, accidental or otherwise. The warranty also does not apply to units in which the sensor element
has been overexposed or gas poisoned. The above warranty is in lieu of all other express warranties,
obligations or liabilities.
This warranty applies only to the PolyGard
®
transmitter. MSR-Electronic-GmbH and IN
TEC
Controls
shall not be liable for any incidental or consequential damages arising out of or related to the use of the
PolyGard
®
transmitters.
If the PolyGard® transmitter needs to be returned to IN
TEC
Controls for service, an RMA number must be
obtained prior to sending.
Specifications subject to change without notice. | USA 140403 | Page 13 of 13
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN
TEC
| relevantsolutions.com/inteccontrols
AT-1193 – UserManual
Polygard® is a registered trademark of MSR | GAADT531193_E_1011.pdf
Specifications subject to change without notice. | USA 160104 | Page 13 of 13
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN
TEC
| relevantsolutions.com/inteccontrols
AT-1193 – UserManual
PolyGard
®
is a registered trademark of MSR-Electronic GmbH | GAADT531193_E_1011
INTEC Controls | 12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.INTEC | inteccontrols.com
Specifications subject to change without notice. | GAADT531193_E_1011 | USA 200211 | Page 13 of 13
AT-1193 V3 – UserManual
