Customer Services (858) 578-7887 & (888) GO IN
TEC
IN
TEC
Controls, 12700 Stowe Dr., Suite 1
0
0, Poway, CA 92064
Fax (858) 578-4633 & (888) FX IN
TEC
www.inteccontrols.com
Specification subject to change without notice.
Printed in USA 140403
Polygard® is a registered trademark of MSR
GAADT531193_E_1011.pdf
PolyGard
®
CL
2
Gas Transmitter
User Manual - AT-1193
Page 04
3 Installation
Note:
Avoid any force (e.g. by thumb) on the sensor element during operation or installation. Electronics
can be destroyed by static electricity. Therefore, do not touch the equipment without a wrist strap connected
to ground or without standing on a conductive floor (acc. to DIN EN100015).
3.1 Mounting Instructions
When choosing the mounting site please pay attention to the following:
The specific weight of Chlorine CL
2
is higher than that of air (factor 2.4).
Recommended mounting height is 0.2 m (0.7 ft.) to 0.3 m (1 ft.) above floor.
Choose mounting location of the sensor according to the local regulations.
Consider the ventilation conditions. Do not mount the transmitter in the center of the airflow
(air passages, suction holes).
Mount the transmitter at a location with minimum vibration and minimum variation in
temperature (avoid direct sunlight).
Avoid locations where water, oil etc. may influence proper operation and where mechanical
damage might be possible.
Provide adequate space around the sensor for maintenance and calibration work.
Duct mounting
Mount only in a straight section of duct with minimum air vortex. Keep a minimum distance of 1 m
(3.5 feet) from any curve or obstacle.
Mount only in a duct system with a maximum air velocity of 10 m/s (2000 ft/min) or less.
Mounting must be performed so that the probe openings are in line with the airflow.
3.2 Installation
Open the cover. Unplug basic PCB carefully from the bottom part.
Fix bottom part by screws vertically to the wall (terminal blocks to the ground).
Replug the basic PCB at X4 and X5 with care. Replace the cover.
4 Electrical Connection
Consider static electricity See 3. Mounting
Installation of the electrical wiring should only be executed by a trained specialist according to
the connection diagram, without any power applied to conductors and according to the
corresponding regulations
Avoid any influence of external interference by using shielded cables for the signal line, but do
not connect the shield.
Recommended cable for analog mode: J-Y(St)Y 2x2x0.8 LG (20 AWG), max. loop resistance 73
/km (20.8
/1000 ft).
It is important to ensure that the wire shields or any bare wires do not short the mounted PCB.
Specifications subject to change without notice. | USA 140403 | Page 4 of 13
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN
TEC
| relevantsolutions.com/inteccontrols
AT-1193 – UserManual
Polygard® is a registered trademark of MSR | GAADT531193_E_1011.pdf
Specifications subject to change without notice. | USA 160104 | Page 4 of 13
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN
TEC
| relevantsolutions.com/inteccontrols
AT-1193 – UserManual
PolyGard
®
is a registered trademark of MSR-Electronic GmbH | GAADT531193_E_1011
INTEC Controls | 12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.INTEC | inteccontrols.com
Specifications subject to change without notice. | GAADT531193_E_1011 | USA 200211 | Page 4 of 13
AT-1193 V3 – UserManual
