background image

Customer Services (858) 578-7887 & (888) GO IN

TEC

IN

TEC

 Controls, 12700 Stowe Dr., Suite 1

0

0, Poway, CA 92064

Fax (858) 578-4633 & (888) FX IN

TEC

www.inteccontrols.com

Specification subject to change without notice.

Printed in USA 140403

Polygard® is a registered trademark of MSR

GAADT531193_E_1011.pdf

PolyGard

®

 CL

2

 Gas Transmitter

User Manual - AT-1193 

Page 11

10 Figures 

Application: Analog mode 

Fig. 1   

Two-wire connection 

4 - 20 mA output signal without 

options 

Three-wire connection 

- VDC output signal 

- 0

 20 mA output signal 

- Relay output 

- LCD display 

- Heating 

Controller

Transmitter

AT-1193

0 V

4-20 mA

24 V

X4

1

2

3

4

5

6

7

0 V

24 VDC_Out

24 VDC

Analog_Out

4-20 mA_Inp

Bus_A

Bus_B

X5

2
3
4
5

1

Controller

Transmitter

AT-1193

0 V

4-20 mA

24 V

X4

1

2

3

4

5

6

7

0 V

24 V_Out

24 VAC/DC

Analog_Out

4-20 mA_Inp

Bus_A

Bus_B

X5

R1

2
3
4
5

1

R2

Option

Relay

N

 N

C

Do not connect power supply at this pin.

(0 VDC, 24 VAC or 0VAC will destroy the transmitter.)

0 VAC/DC
24 VAC/DC

Do not connect 24 VAC at pin 2 and pin 4

or +24 VDC at pin 2 and 0 VDC at pin 4!!

Short-circuit = R 10 Ohm burns up!!

Transmitter

AT-1193

X4

1

2

3

4

5  10 

Analog_Out

Specifications subject to change without notice. | USA 140403 | Page 11 of 13

12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN

TEC

 | relevantsolutions.com/inteccontrols

AT-1193 – UserManual

Polygard® is a registered trademark of MSR | GAADT531193_E_1011.pdf

Specifications subject to change without notice. | USA 160104 | Page 11 of 13

12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN

TEC

 | relevantsolutions.com/inteccontrols

AT-1193 – UserManual

PolyGard

®

 is a registered trademark of MSR-Electronic GmbH | GAADT531193_E_1011

INTEC Controls | 12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.INTEC | inteccontrols.com

Specifications subject to change without notice. | GAADT531193_E_1011 | USA 200211 | Page 11 of 13

AT-1193 V3 – UserManual

Содержание AT03-005














Отзывы: