Instramed DUALMAX Скачать руководство пользователя страница 3

Страница: 3 / 219

III

Battery use

ATTENTION: observe the battery charge maintenance instructions.

First use

Before using the DualMax for the first time, the equipment must receive a full

battery charge. In order to do this, the equipment needs to be connected to an

electric current for at least eught hours.

Occasional use

Even when disconnected (stand-by), the DualMax executes internal routines

checking the status of the equipment. In spite of this procedure entailing a low

power consumption, the battery charge may be consumed.
Therefore, whenever the device has not been connected to an electric current for

more than 20 days, it is advisable to execute a full battery charge. If this procedure

is not performed, there is a risk of draining the battery and consequently being

unable to use the DualMax in its portable configuration (not connected to the

electric current).

Storage

The battery must be removed from the equipment in case it is stored or not used.

Replacement

Every battery has a determined lifetime, which is the possible quantity of full charge

and discharge cycles, without loss of performance. When the appliance has a drop

in performance of the battery, with low autonomy, request a new unit from Instramed

technical assistance.
The battery can be replaced following the procedures described on the chapter

“Care and maintenance”.

Battery replacement is recommended every 02 (two) years or when the runtime is less

than 01 (one) hour.

ATTENTION: the equipment is capable of operating with only one battery

connected.

ATTENTION: when servicing the batteries, it is obligatory to change only

one battery at a time, leaving the other battery in the device, so that it can

continue to operate at that moment.

Содержание DUALMAX




























































































































































































































Результаты поиска

Содержание DUALMAX

Отзывы:

Похожие инструкции для DUALMAX

Бренды по названию

Популярные бренды

Instramed DUALMAX, Руководство пользователя

Результаты поиска

Содержание DUALMAX

Отзывы:

Похожие инструкции для DUALMAX

Бренды по названию

Популярные бренды