Innovative BV20 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 48

background image

Copyright Innovative Technology Ltd 2008 GA794-2

8 ROUTINE MAINTENANCE

The BV20 Validator has been designed to minimise any performance variation over

time. Much of this is achieved by careful Hardware and Software design.

However, depending upon the environment in which it is used the BV20 may at some

time require re-calibration.

8.1 RE-CALIBRATION

The BV20 has an in-built self-calibration system that maintains the optical sensors at

their best operating point. However if the BV20 is disassembled for any reason it will

need to be re-calibrated. Re-calibration may only be performed under license from ITL,

contact

[email protected]

for further details.

This can be performed in conjunction with the diagnostics software option in the ITL BNV

Currency Manager Program and help menus supplied with this program.

9 SUPPORT TOOLS

The following support tools are available for use with the BV20 Bank Note Validator:

•

ITL Bank Note Validator Currency Manager Software.

•

Configuration Cards

.

•

Validator Programming System (DA3).

•

Downloads from the Innovative Technology Ltd website:

www.innovative-

technology.co.uk

•

E-mail Support via

[email protected]

9.1 CONFIGURATION CARDS

For full details of the use and function of the Configuration Cards please see

Appendix D – Configuration Cards

NV200 CASHBOX LOCK FITTINGS

NV200 Operations Manual 25

BV20 Operations Manual

29

«
...
27
28
29
30
31
...
»

Содержание BV20

















































Отзывы:

Нет отзывов

Похожие инструкции для BV20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды