manualshive.com logo in svg

INIM Electronics SmartLine Series, Инструкция по установке и программированию

Поделиться
Скачать
INIM Electronics SmartLine Series Скачать руководство пользователя страница 20

20

User interface

Conventional fire detection control panel

5.1.2 Signalling

[E]

EVACUATE

If this button is pressed 
during active pre-alarm 
conditions, the system 
will override the 
programmed pre-alarm 
time and generate an 
instant alarm.

If this button is pressed when 
pre-alarm conditions are not 
active, the system will generate 
a panel alarm.

[F]

INVESTIGATE

If this button is pressed during 
active pre-alarm conditions, the 
system will add the preset 
investigation time to the 
running pre-alarm time (this 
operation can be done once 
only).

The extended alarm delay will allow 
authorized building occupants and/
or security staff to check and verify 
the fire hazard.

Extinguishant board commands

[G] DISABLE 

EXTINGUISH

If this button is pressed once, 
the system will disable fire-
extinction commands. If this 
button is pressed again, the 
system will re-enable fire-
extinction commands.

This button can be used during 
testing and maintenance of the fire 
extinction devices.

[H] DISABLE AUTO

If this button is pressed once, 
the system will disable 
automatic fire-extinction 
commands generated by the 
board. If this button is pressed 
again, the system will re-enable 
automatic fire-extinction 
commands generated by the 
board.

[I]

DISABLE 
MANUAL

If you push this button once, 
the system will disable manual 
extinguish commands. If you 
push this button again, the 
system will re-enable manual 
extinguish commands. Refer to 

paragraph 6.14 - Connecting 
the Extinguishant module 
(optional system enhancement 
tool)

.

LED

If On solid:

If Blinking:

Note

[J]

Display

See 

Chapter 8 - Introduction to 

Programming from the panel.

[K]

SILENCED

(yellow)

Indicates that the 
system has been 
silenced.

[L]

RESET 
INHIBITED

(yellow)

In the event of pre-
alarm/alarm, indicates 
that reset commands are 
not allowed. Reset will 
be allowed when all 
outputs have been 
silenced and this LED 
goes Off.

This feature ensures that persons 
responsible for the safety of the building 
and its occupants do not reset the system 
without first silencing the outputs, and 
evaluating the alarm. The silence operation 
will stop the signalling devices and restore 
quiet thus allowing the operator to consider 
the best way to proceed. The operator will 
then be able to reset the system and 
restore standby status.

Command

Access level 1

Access level 2

Note

Содержание SmartLine Series









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды