Ingersoll-Rand Rotary Screw Air Compressor, Информация о безопасности продукции

Страница: 8 / 48

EN
80446313 Rev A EN-8
Do not touch the airend, driver or air discharge piping until one hour after shutdown. Surface temperatures of these areas are extremely high when
operating. Wear heat-resistant gloves and long sleeves when working around these areas.
Shut off the compressor before entering the sound enclosure.
Do not access any pressurized areas of the system while the compressor is operating.
Do not install accessories or parts that have not been approved by Ingersoll Rand.
Do not operate the compressor with the coolant fill plug removed.
Ensure that the compressor does not exceed the rated operating pressure.
If a safety valves activates, immediately press the emergency stop button and investigate the cause of excessive pressure.
Avoid ingestion, skin contact and inhalation of fumes.
The compressor can operate in a pressurized shutdown mode. If the compressor stops automatically, the airend, separator tank and oil system can contain
high pressure air. Press the emergency stop button to relieve the air pressure. Unscrew the coolant fill plug to vent any remaining pressure through the
vent hole. Vent air pressure downstream of the separator tank.
Drain tanks daily or after each use.
Do not use a receiver tank or similar vessels that fail to meet the design requirements of the compressor.
Do not drill into, weld or otherwise alter the receiver tank or similar vessels.
Do not use air tools or attachments without first determining the maximum pressure recommended for that equipment.
Keep hands, loose clothing, long hair and jewelry away from moving parts.
Safety Information -When Servicing the Product
WARNING
Ensure all activities involving maintenance of the compressor comply with all applicable codes, laws, regulations, standards, and specifications (local, state,
country, federal, etc.).
Personnel
The compressor instruction manual contains instructions and technical data to cover all routine operation and scheduled maintenance tasks. Major
overhauls are outside the scope of the compressor instruction manual and should be referred to an authorized Ingersoll Rand service provider.
Ensure maintenance personnel are adequately trained.
Before Performing Maintenance
Disconnect the main electrical power line.
Disconnect any separate control lines.
Isolate all residual electrical power sources (mains and battery).
Ensure all air pressure is fully discharged and isolated from the system.
Vent all air pressure from the compressor. Verify this by slowly unscrewing the lubricant/coolant fill cap one turn. Unscrewing the fill cap opens a vent hole,
drilled in the cap, allowing pressure to release to atmosphere. Do not remove the fill cap until all pressure has vented.
Use precautionary measures to prevent the possibility of applying power to the compressor when maintenance work is in progress. Lockout/ tagout the
power supply and display warning signs indicating that maintenance work is in progress.
Prior to attempting any maintenance work on a running machine, ensure that:
the work carried out is limited to only those tasks which require the machine to run.
the work carried out with safety protection devices disabled or removed is limited to only those tasks which require the machine to be running with
safety protection devices disabled or removed.
all hazards present are known (e.g. pressurized components, electrically live components, removed panels, covers and guards, extreme temperatures,
inflow and outflow of air, intermittently moving parts, safety valve discharge, etc.).
During Maintenance
Attempt repairs only in clean, dry, well lighted and ventilated areas.
Never make any modifications, additions or conversions which might affect safety without the approval of Ingersoll Rand. This also applies to the
installation and adjustment of safety devices and valves as well as to welding work on load-bearing components.
During maintenance and when making repairs, keep dirt away from parts by covering parts and exposed openings with clean cloth or paper.
Use suitable equipment for lifting heavy items and ensure loose components are adequately supported to eliminate risk of dropping.
When lifting the driver unit from the compressor, use all the lifting eyes provided.
Take precautions to prevent personal contact with hot coolant.
Do not lubricate parts with flammable or volatile liquids such as kerosene, diesel or jet fuel. Use only recommended lubricants.
Do not use flammable or volatile liquids such as kerosene, diesel or jet fuel for cleaning or degreasing. Use a non-flammable, non-conductive, safety
solvent cleaner and degreaser designed for industrial cleaning. Follow the manufacturer’s instructions closely. Use safety solvents in a well-ventilated area
and always wear the appropriate personal protective equipment.
When using any form of liquid for cleaning, ensure that all electrical components are protected or covered to prevent ingress of liquid.
Open condensate valves slowly as condensate may be discharged at high pressures. Wear hearing protection when opening valves.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•

•
•

•
•
•
•
•
•
•
–
–
–

•
•
•
•
•
•
•
•
•
•