Inficon IMM-200 Скачать руководство пользователя

Страница: 19 / 67

INFICON

Introduction and Specifications | 4

074-733-P1A IMM-200 Operating Manual

19 / 67

4.6 Initial Power-On Verification

A preliminary functional check of IMM-200 can be made before installation. It is not

necessary to have sensors or communication cables connected to do this.

The green IMM-200 Status light is used to identify if the unit is operating correctly, or if

there is a failure condition.

Connect 24 V (dc) to the power connector using either one of the power supplies listed

in Parts and Options Overview or a user supplied power supply with a power rating

indicated by Power, in Specifications.

If a user supplied power supply is used, INFICON recommends the power connection

to IMM-200 use a Kycon connector, part number KPPX-4P. Pins 3 and 4 carry +24 V

(dc), pins 1 and 2 are ground. Whenever a user supplied power supply is used, the

connector shield on the 24 V power cable must be connected to the mains protective

earth ground terminal through the user supplied power supply.

If a good crystal is connected, the Status LED illuminates and remains steadily on.

This status indicates proper operation of IMM-200. If a good crystal is not connected,

the Status LED illuminates 1 s on,1 s off, to indicate a crystal fail. IMM-200 is in Idle if

the Status LED flash pattern is 1 s on, 4 s off.

If the Status LED has the following flash patterns, please contact INFICON as an error

exists. To contact INFICON service, refer to How to Contact Us [

}

15].

LED State

Description

0.5 s on, 0.2 s off, 0.5 s on, 1 s off

Invalid firmware or POST fail

If the Status LED is off, confirm that the proper power is connected to IMM-200. If the

proper power is connected but the LED is still off, contact INFICON service.

Содержание IMM-200




































































Результаты поиска

Содержание IMM-200

Отзывы:

Похожие инструкции для IMM-200

Бренды по названию

Популярные бренды

Inficon IMM-200, Руководство по эксплуатации

Результаты поиска

Содержание IMM-200

Отзывы:

Похожие инструкции для IMM-200

Бренды по названию

Популярные бренды